110245

Makita 2414 Manual

6
Zoom out
Zoom in
Previous page
1/16
Next page
6
ENGLISH
Explanation of general view
1 Safety guide
2 Shaft lock
3 Socket wrench
4 Cut-off wheel
5 Inner flange
6O-ring
7Spindle
8 Ring
9 Outer flange
10 Hex bolt
11 Screw
12 Spark guard
13 Guide plate
14 Hex bolts
15 Vise plate
16 Vise nut
17 Vise handle
18 Spacer block
19 Straight piece of wood (Spacer)
20 Over 190 mm long
21 Over 45 mm wide
22 Over 65 mm wide
23 Diameter of workpiece
24 Spacer block
25 Vise
26 Width of spacer block
27 Blocks
28 Switch trigger
29 Lock-off button
30 Lock button
31 Handle
32 Uncut portion
33 Workpiece
34 Wing bolt
35 Under cover
36 Limit mark
37 Screwdriver
38 Brush holder cap
SPECIFICATIONS
Model 2414B
Wheel diameter ...................................................................................................................................................355 mm
Hole diameter .....................................................................................................................................................25.4 mm
No load speed (min
-1
) ............................................................................................................................................ 3,800
Dimensions (L x W x H)
With under cover .............................................................................................................500 mm x 280 mm x 620 mm
Net weight
For tools with European type safety guide and under cover...............................................................................18.7 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.26 Ohms it can be presumed that
there will be no negative effects.
The mains socket used for this device must be protected
with a fuse or protective circuit breaker having slow trip-
ping characteristics.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
ADDITIONAL SAFETY RULES
ENB066-1
1. Wear protective glasses. Also wear hearing pro-
tection during extended periods of operation.
2. Use only wheels recommended by the manufac-
turer which have a maximum operating speed at
least as high as “No Load RPM” marked on the
tool’s nameplate. Use only fiberglass-reinforced
cut-off wheels.
3. Check the wheel carefully for cracks or damage
before operation. Replace cracked or damaged
wheel immediately.
4. Secure the wheel carefully.
5. Use only flanges specified for this tool.
6. Be careful not to damage the spindle, flanges
(especially the installing surface) or bolt, or the
wheel itself might break.
7. Keep guards in place and in working order.
8. Hold the handle firmly.
9. Keep hands away from rotating parts.
10. Make sure the wheel is not contacting the work-
piece before the switch is turned on.
11. Before using the tool on an actual workpiece, let
it simply run for several minutes first. Watch for
flutter or excessive vibration that might be
caused by poor installation or a poorly balanced
wheel.
12. Watch out for flying sparks when operating.
They can cause injury or ignite combustible
materials.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 2414 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 2414 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info