494089
8
Zoom out
Zoom in
Previous page
1/44
Next page
MACROM INGLESE 44.05/07 14 OTTOBRE 1992 10
CONNECTIONS
CONNECTIONS (Fig. 2, page 3)
13 Positive output terminal, speaker A, or positive output speaker E
14 Negative output terminal, speaker A
15 Positive output terminal, speaker B
16 Negative output terminal, speaker B, or negative output speaker E
17 Positive output terminal, speaker C, or positive output speaker F
18 Negative output terminal, speaker C
19 Positive output terminal, speaker D
20 Negative output terminal, speaker D, or negative output speaker F
21 2x20/2x25 A fuses
22 Power supply terminal +12 V to the battery (BATT)
23 Terminal for connection of the negative ground lead (GND)
24 Terminal for remote switch-on (REMOTE)
25 Check control status indicator
CONNECTIONS:
Battery lead: Connect the terminal BATT 22 to the battery cable of the car by means of a
(yellow) cable of adequate section.
Do not connect this lead to circuits existing within the electric system of the car. In order to avoid
damage to the car it is imperative that this lead be fitted with a fuse (not provided) as near as
possible to the battery. This connection is the to be carried out last.
Remote switch-on lead: Connect the remote switch-on lead (REMOTE) or the control lead of
the power antenna coming from the head unit (blue) to the REMOTE 24 terminal of the amplifier.
NOTE: In case this lead is not connected, the amplifier will not be switched on when the head
unit is switched on. If your head unit is not fitted with an outlet for a power antenna, a quick-break
lever switch (SPST) shall be installed between the power source (+12 V) and the remote switch-
on lead and connected to the REMOTE 24 terminal so as to provide for manual switch-on of
the amplifier.
Ground lead: Secure the ground lead (black) to a clean spot on the car chassis and to the GND
terminal 23 . Make sure that there is electric continuity between this spot and the negative
terminal of the battery. The ground cable should be as short as possible; in case more than one
amps are used, connect all the ground connectors to one spot.
Fuse: In case of fuse replacement make sure to replace it with a fuse of the same amperage.
The use of fuses with the wrong amperage may seriously damage the components of the unit.
Speaker outlet terminals: Make sure to keep the right polarity and phase on connecting the
speakers. This includes the control of the right polarity, positive (+) and negative (-).
NOTE: The negatives of the speakers should NEVER be connected witch each other and no
common ground lead must be used.Non adequately isolated wires should never come into
contact with each other, with metallic parts of the car or with the ground lead.
RCA input connectors: Connect the Pre output leads of your head unit to the RCA input
connectors by means of RCA extension cables (90.05-90.10-90.25-90.50 by MACROM).
Make sure to observe the right channel designation: left L (white) and right R (red).
1.
2.
3.
4.
5.
6.
10
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Macrom 44.05 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Macrom 44.05 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info