166337
20
Zoom out
Zoom in
Previous page
1/26
Next page
20
CONTROLLI & INDICATORI
8 • CONNETTORI DI USCITA RCA PRE-OUTPUT: Collegare ad un supplementare
amplificatore che utilizzerete secondo il modo selezionato precedentemente.
9• CONNETTORE SPEAKER: Uscite per il collegamento degli altoparlanti.
L’amplificatore permette il collegamento di altoparlanti di impedenza minima di 1 ohm per
canale in configurazione stereo, mentre per il collegamento in mono “Bridged” un impedenza
di 2 ohm.Qualora si utilizzasse la configurazione 3 canali l’impedenza totale non deve
superare il valore minimo di 2 ohm.
Assicurarsi di osservare la corretta polarità e la fase nel collegamento degli altoparlanti.
Non lasciate che cavi non adeguatamente isolati vengano in contatto con la massa, parti
metalliche dell`auto o facciano contatto fra di loro.
10 • FUSIBILE: Quando sostituite i fusibili, assicuratevi di sostituire il fusibile esaurito con uno
dello stesso amperaggio. L`uso dei fusibili scorretti potrebbe comportare gravi danni ai
componenti.
11 • CONNETTORE + BATT: Collegare direttamente al + della batteria tramite un fusibile
posto vicino alla stessa con un cavo di sezione adeguata. Non collegate questo cavo con il
circuito elettrico dell`auto (p. es. il circuito delle plafoniere o dell`autoradio, ecc.).
12 • CONNETTORE GND: Collegare il morsetto di massa tramite un cavo di sezione
adeguata ad un punto pulito della parte metallica dello chassis dell`automobile, (se possibile
ad una vite già installata).
13 • CONNETTORE REMOTE-ON: va collegato al filo di uscita di accensione remote-on
(accensione a distanza) o dell’antenna automatica provenienti dall’unità principale. Questo
permette di accendere e spegnere il 42.29 tramite l’unità principale.
14 • INDICATORE CHECK CONTROL: Questo led indica lo stato di funzionamento
dell`amplificatore.
BIANCO: l`unità è spenta
VERDE: l`unità funziona perfettamente.
ROSSO: l`unità è in protezione. Il 42.29 è provvisto di tre protezioni,
- Surriscaldamento, nel caso vi siano errori d`installazione l`unità entra in protezione prima di
danneggiarsi. Appena la temperatura tornerà normale, l`unità riprenderà automaticamente il
normale funzionamento.
- Sovraccarichi, nel caso più altoparlanti vengano collegati all`amplificatore e, l`impedenza
totale scenda sotto i limiti sopportabili “1 ohm”, l`amplificatore si autoprotegge entrando in
protezione. Per riprestinare il funzionamento è necessario spegnere e riaccendere l`unità
principale.
- Corto circuito in uscita, in caso di cortocircuito sulle uscite altoparlanti l`unità entra in
protezione per prevenire seri danni ai transistor finali. Il ritorno allo stato di normale
funzionamento si ottiene rimuovendo il cortocircuito e riaccendendo l`unià principale.
++
+
BRIDGED
L R
++
+
BRIDGED
L R
++
+
BRIDGED
L R
Configurazione 3 canali Configurazione 2 canali Configurazione 1 canale
O/M 42.29 26/06/02 10:19 Page 20
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Macrom 42 29 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Macrom 42 29 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info