167699

Mac Audio mpx 2000 Manual

13
Zoom out
Zoom in
Previous page
1/80
Next page
13
GB
3. IMPORTANT INSTALLATION INFORMATION
• This appliance may only be connected to a 12 volt system with negative ground.
• The heat radiated when the amplifier is used means that sufficient air circulation is
required at the place of installation. It is very important that the cooler's cooler ribs
do not contact any metal plating or any surfaces which could impair air circulation.
The amplifier may not be installed in small confined spaces or spaces without air
circulation (e.g. spare wheel recess or under the vehicle carpeting). Installation in
the boot is recommended.
• Install the amplifier in such a way that it is protected as far as possible against
vibrations and dust and dirt.
• Make sure that the input/output cables are sufficiently distant from the power supply
cables as otherwise interference may occur.
• Make sure that the fuse and operating elements are accessible after installation.
• The appliance's reliability and performance depend on the quality of installation.
Preferably get an expert to install the system, particularly if you want to install several
loudspeakers or a complex multi-way system.
4. CONNECTIONS
4.1 POWER SUPPLY AND AUTOMATIC SWITCHING ON
Important notice: Before commencing the installation, disconnect the plus
terminals from the car battery in order to prevent short
circuits.
The power cabling usually installed in on-board car networks is not sufficient for a power
amplifier's demands. Make sure that the power lines to GND and to the +12 V terminal
have been sufficiently specified. A cable cross-section of at least 6 mm² (MPX 2000) /
10 mm² (MPX 2500) must be used to connect the battery to the amplifier's terminals.
First connect the amplifier's GND terminal to the battery's minus pole. It is very important
that the connection is good. Dirt residues must be carefully removed from the battery's
connection point. A loose connection may cause malfunctions or interference noise or
distortion.
The +12 V amplifier connection must then be connected with a power cable possessing
an integrated fuse to the battery's plus pole. The fuse must be located close to the battery,
the length of cable from the battery's positive pole to the fuse must be less than
60 centimetres for safety reasons. Only insert the fuse when all installation work, including
the connection of the loudspeakers, has been completed.
Now connect the car hi-fi receiver's remote control connection to the amplifier's REM
control jack. A cable with a cross-section of 0.75 mm² is sufficient for connecting the
amplifier's REMOTE connection and the control device.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Mac Audio mpx 2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Mac Audio mpx 2000 in the language / languages: English, German, French as an attachment in your email.

The manual is 0,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info