522905

M-System MST-90 Manual

3
Zoom out
Zoom in
Previous page
1/20
Next page
C) Decreases speed down to minimum speed. If pressed for 2" the motor is turned off.
D) Activates the motor (calling the last speed used) and increases the speed until reaching maximum.
E) FILTER ALARM/TIMER RESET: when pressing the key during display of the filter alarm (motor off) it resets the hour
counter. When pressing the key when the motor is running, the TIMER is activated and the hood will automatically be switched
off after 5 minutes.
L1) The 4 green LEDs indicate the running speed.
L2) When the LED is red (motor off) it indicates the FILTER ALARM. When the LED is green (flashing) it indicates that
the TIMER has been activated with the key E.
FILTER ALARM:
After 30h of operation, the LED L2 turns RED. It indicates that the grease filters need to be cleaned.
After 120h of operation, the LED L2 turns RED and flashes; It indicates that the grease filters need to be cleaned and
the charcoal filters replaced.
After cleaning the grease filters (and/or replacing the charcoal filters), restart the hour counter (RESET) by pressing the
key E during display of the filter alarm.
CONTROLS shown in Fig. 19:
A) LIGHTS on/off switch.
1) Activates the motor at the first speed (the icon lights-up). By pressing on the icon for about 2 seconds the motor will stop.
2) Activates the motor at the second speed (the icon lights-up). All of the other icons relative to the speed remain switched off.
3) Activates the motor at the third speed (the icon lights-up). All of the other icons relative to the speed remain switched off.
4) Activates the motor at the fourth speed (the icon lights-up). All of the other icons relative to the speed remain switched off.
B) Activates the TIMER (the icon lights-up). By activating the Timer (5 minutes), the motor will stop automatically after 5 minutes.
C) FILTER ALARM. After 30 working hours, the icon lights up to indicate that the grease filter/s must be cleaned.
After 120 working hours, the icon flashes to indicate that the grease filter/s must be cleaned and the charcoal filters replaced.
To re-start the hour - counter, reset by pressing on the icon while it is lit (or while it flashes).
Grease filters: special attention must be given to the grease filters which must be periodically cleaned, whenever
the grease filter alarm trips. For instructions of the filter Alarm, refer to the Controls paragraph.
- Removing the grease filter (for models with metal panels): Remove the front panels by gripping them on the right (or
left) and pulling until the 2 internal pins are released. Operate in the same way on the opposite side of the panel;
slightly move the panel upwards until the 2 tabs slip out of the slots (Fig. 3). Remove the grease filters by pushing
the catch downwards and turning the filter outwards (Fig. 4).
- Removing the grease filter (for models with glass panels): Open the front panels gripping them at the bottom (Fig.5).
Remove the grease filters by pushing the catch downwards and turning the filter outwards (Fig. 4).
Charcoal filters: if the filtering version appliance is used, the charcoal filters will have to be periodically replaced
when the charcoal filter alarm trips. For instructions on the filter Alarm, refer to the Controls paragraph.
- Remove the charcoal filter (for models with metal panels): Remove the upper panel gripping it on the right (or left)
and pulling until the 2 internal pins are released. Operate in the same way on the opposite side of the panel; slightly
move the panel upwards until the 2 tabs slip out of the slots (Fig. 3). Remove the upper grease filter by pushing the
catch downwards and turning the filter outwards (Fig. 4). Remove the charcoal filters by turning them clockwise (Fig.
20).
- Removing the charcoal filter (for models with glass panels): Open the upper panel by gripping it at the bottom (Fig.5).
Remove the grease filter by pushing the catch downwards and turning the filter outwards (Fig. 4). Remove the
charcoal filters by turning them clockwise (Fig. 20).
Lighting (Fig.21): To replace the halogen lamps, open the cover by prising in the slots. Replace with lamps of the
same type. WARNING: Do not touch the new lamp with bare hands.
This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling
of this product. The symbol on the product indicates that this product may not be treated as household waste. Instead
it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal
must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information
about treatment, recovery and recycling of this product, please contact your local city office, your household waste
disposal service or the shop where you purchased the product.
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for M-System MST-90 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of M-System MST-90 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info