Manual Lynx Aurora LT-TB (page 32 of 55) (English)

587002

Zoom out

Zoom in

1/55

 Mutes

The “M” Icon below the fader is for the Mutes. This switch Mutes or UnMutes

the input signal routed to an output. As with the faders, this control is specific to

the patch point between the Input Source, and the selected output. It does not

control whether the input signal itself is muted, or whether that input signal can be recorded.

When the “M” button is blue like this , then the Mute is ON, and no signal will pass to the

selected output. When the “M” button is gray, like this , then the Mute button is OFF, and

signal WILL pass to the selected output.

Inputs are Muted by default. When an output is selected from the outputs pane, inputs need to

be un-muted to become active. When an input source is no longer being monitored, then it is

good practice to Mute it again so that unintended mic bleed or system noise is not corrupting

the signal path.

 Channel Link

In between the two Mute buttons for a pair of Inputs, is the channel link control: . This

control toggles the linked state for a pair of faders and mutes. If two channels ARE linked,

then moving the fader for one of them will move both channels. Similarly, if one is muted

then both will mute. If the faders between the channels are offset, when one is moved the

other will snap to the same position. The linked state also impacts the Pan controls. If one

pan pot is moved to the left the other will move a corresponding amount to the right. For

instance, if the left pot is set to -25, the right channel will pan to +25.

Linked is the default state for pairs of inputs. To “un-link” a pair, click on the link icon and it

will change to a single circle: . In this state, the mute, fader and pan controls operate on a

single channel independently.

 Record Source Label

This identifies the Record Source that is applicable to the fader, pan, mute and input select

controls. The Record Source is the driver device that you will see from an audio software

application. For instance, if you are viewing the Record 3+4 fader strip, and you have Analog

Inputs 3+4 assigned to it, then when you select Record 3+4 in a track in your recording

software, you will get signals from Analog Inputs 3+4 streaming to that track.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Lynx Aurora LT-TB in the language / languages: English as an attachment in your email.

The manual is 0,99 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Lynx Aurora LT-TB Manual

Product: