599305

Lowrance LCX-112C Manual

212
Zoom out
Zoom in
Previous page
1/232
Next page
202
Restore Defaults command from your Port Engine Interface Advanced
Options menu, only the settings for the Port Engine Interface will be
reset to factory defaults. Other engine interfaces on the network will
not be affected.
To restore default settings:
1. Press MENU| MENU, use ↑ ↓ to select NMEA 2000 and press ENT. The NMEA
2000 menu will appear with five options: Bus Setup, Fuel Management,
NMEA 2000 Alarms, Waypoint Sharing and Backlight Synchronization.
2. Highlight
BUS SETUP and press ENT.
3. Use ↑ ↓ to select the desired fluid level and press
ENT. The Device
Configuration menu will appear.
4. Highlight
ADVANCED OPTIONS and press ENT.
5. Select
RESTORE DEFAULTS and press ENT. The following message will
appear: Are you sure you wish to change this device's configuration?
6. Highlight
YES and press ENT. Press EXIT repeatedly to get back to the
main display.
NOTE:
The Suzuki Engine Interface Device Configuration menu contains
two Engine Trim calibration commands, which will be addressed in
the next segment of this section, Calibrating EP Sensors.
Calibrating EP Sensors
The factory calibration settings for the EP-10 Fuel Flow, EP-15 Fluid
Level and Suzuki Engine Interface should be adequate for the majority
of applications, so calibration will not be necessary in most cases.
EP-10 Fuel Flow Calibration
The default calibration for the EP-10 Fuel Flow is adequate in most
cases, but if Fuel Used readings are off by more than 3 percent,
calibration is recommended.
To check fuel flow accuracy:
Select Fuel Used to be shown as Overlay Data on your unit's main display.
Refer to the Overlay Data segment of this manual for instructions on how
to select Fuel Used data as Overlay Data.
1. After selecting Fuel Used as overlay data, fill up your tank and press
MENU|MENU.
2. Select
NMEA 2000 and press ENT.
3. Highlight
FUEL MANAGEMENT and press ENT. Select TANK LOCATION and press ENT.
4. Use ↑ ↓ to select the location (Port, Center or Starboard) of the fuel
flow you want to calibrate and press
ENT.
5. Highlight
FILL TANK and press ENT. The following confirmation
message will appear: Are you sure you wish to Fill Tank?
… 212 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lowrance LCX-112C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lowrance LCX-112C in the language / languages: English as an attachment in your email.

The manual is 12,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info