470141
11
Zoom out
Zoom in
Previous page
1/28
Next page
11
A transducer can not shoot through wood or metal hulls. Wood and metal hulls
require either a transom mount or "thru-hull" installation. For shoot-thru-hull appli-
cations many boat hulls have a at keel pad that offers a good transducer mounting
surface.
If you are using a Skimmer transducer versus a Pod transducer for this installation,
make sure the Skimmer transducer is oriented so the nose of the transducer is facing
the bow (front) of the boat. Also, if the transducer has a built in temp sensor, it will
only show the temperature of the hull, not the water temp.
Before you epoxy the transducer to the hull, make sure the area is clean, dry and free
of oil or grease. The surface of the hull must be at so the entire transducer face is
in contact with the hull. Also, make sure the cable is long enough to reach the sonar
unit.
Apply pressure to hold the transducer in place while the epoxy sets. Be careful not
to move the transducer while the epoxy is setting. Allow the epoxy to set before
moving the boat. When nished, the face of the transducer should be parallel with
the hull with a minimum amount of epoxy between the hull and transducer. After the
epoxy has set, route the transducer cable to the sonar unit.
Sand both the inside surface of the hull,
where the transducer is to be epoxied, and
the face of the transducer.
Start with a rougher grit sandpaper, such
as 60 grit, and nish with a smoother grit,
such as 160 grit, sandpaper. Sand the in-
side surface of the hull until it is smooth
to the touch.
The sanded area should be about 1-1/2
times the diameter of the transducer. Af-
ter sanding, clean the hull and face of the
transducer with an alcohol wipe to remove
any sandpaper grit and dust.
Apply a thin layer of epoxy (about 1-16"
or 1.5 mm) on the face of the transducer
and the sanded area on the hull. Make
sure there are no air pockets in the ep-
oxy layers.
Press the transducer into the epoxy, twist-
ing and turning it to force any air bubbles
out from under the transducer face. Stop
pressing when it bottoms out on the hull.
1. Sand face
of transducer
and bottom of
hull.
2. Apply ep-
oxy to face
of transducer
and bottom of
hull.
3. Epoxy transducer to hull.
To bow
Hull
Epoxy
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lowrance HDS-5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lowrance HDS-5 in the language / languages: English as an attachment in your email.

The manual is 5,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Lowrance HDS-5

Lowrance HDS-5 Quick start guide - English - 6 pages

Lowrance HDS-5 User Manual - English - 129 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info