522471
81
Zoom out
Zoom in
Previous page
1/152
Next page
83
User Manual
searching for MIRROR C-CARDs. When one or more MIRROR C-CARD is found (in
one or both chart plotters) a special connection is established between the chart plotters to
habilitate the MIRROR C-CARDs. If a regular C-CARD which has previously activated a
MIRROR C-CARD is removed, even the MIRROR C-CARD will be not read anymore on
the other unit.
4.8 C-LINK NAVIGATION DATA TRANSFER
This function allows transferring C-Link Navigation Data (Route Name, Destination
ID & Position, Next Waypoint ID & Position, Total Route length, Fuel Consumption Rate,
ETA, TTG etc.) between two chart plotters linked through the C-Link system. The chart
plotters can be set to operate in two modes:
MASTER mode (Primary chart plotter that sends data)
SLAVE mode (Secondary chart plotter that receives data)
When the navigation is activated on the Master chart plotter, the C-Link Navigation
Data will be continuously sent to the Slave until the navigation is active. If the Master is
navigating to a Single Destination, the Slave will show the Destination position and activate
the navigation to it. If the Master is navigating to a Route, the Slave will show the Route Leg
composed by the Destination and the Waypoint after the Destination (Next Waypoint) and
activate the navigation to it. Any variation to the current C-Link Navigation Data will be
transferred from the Master to the Slave. The Slave will be provided with a few dedicated
pages to show the C-Link Navigation Data received from the Master.
4.8.1 OPERATIONS
4.8.1.1 Introductive elements
It is important remark, once more, that this function does not transfer the whole
Route but just the information relative to the navigation. Such information will be removed
from the Slave chart plotter as soon as the navigation is terminated. C-Link Navigation
Data is exchanged by using two NMEA-0183 C-MAP proprietary sentences: $PCMPN,1
and $PCMPN,2. When the navigation is activated on the Master, it starts outputting the
C-Link Navigation Data. If the Slave is connected, all C-Link Navigation Data received are
stored in its memory and the navigation is started. The information sent by the Master
consists of the following values:
Navigation mode (to Single Destination/to a Route )
Route Name*
81


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lorenz COMPACT X7 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lorenz COMPACT X7 in the language / languages: English as an attachment in your email.

The manual is 2,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info