612983
75
Zoom out
Zoom in
Previous page
1/289
Next page
6
Advanced Configuration
Linksys WUMC710
6
Après avoir configuré le connecteur multimédia en suivant les étapes du
guide d’installation rapide, le connecteur multimédia est prêt à être utilisé.
Cependant, si vous souhaitez modifier ses paramètres avancés, utilisez
l’utilitaire basé sur le navigateurWeb du connecteur multimédia. Le présent
chapitre explique chaque pageWeb de l’utilitaire et les principales options
proposées sur chacune. Vous pouvez accéder à l’utilitaire depuis un navigateur
Web sur un ordinateur connecté au réseau du connecteur multimédia.
The browser-based utility has these main tabs: Setup, Wireless, Administration,
and Status. Additional tabs will be available after you click one of the main tabs.
How to access the browser-based utility
Use a web browser to access the browser-based utility.
If the media connector is connected to a network with a DHCP server (usually
the network router), then the media connector will obtain its IP address from
the DHCP server. If there is no DHCP server, then the media connector will use
its default IP address, 10.100.1.1 (for example, if the media connector is not
connected wirelessly to any device but is connected directly to a computer
with an Ethernet cable). If you set a permanent static IP address on the media
connector through the browser-based utility, then enter the static IP address
instead.
NOTE
If you do not know the media connectors IP address, then find its
IP address in the DHCP clients table of your router. (Refer to the
documentation for your router.)
If you cannot locate the media connectors IP address, you can reset
the media connector; press the Reset button on the media connector
for approximately five seconds, using a straightened paper clip. This
will reset the media connector back to the factory default settings.
The media connector will request an IP address from the DHCP server
(usually the network router). If no DHCP server is found (for example,
if the media connector is not connected wirelessly to any device but
is connected directly to a computer with an Ethernet cable), then the
media connector will use its default IP address, 10.100.1.1, until it
detects a DHCP server and is assigned a dynamic IP address.
Launch your web browser, and enter the media connectors IP address (the
default setting is 10.100.1.1) in the Address field. Press Enter.
A password request screen appears. (Non-Windows 7 users will see a similar
screen.) Leave the User name field blank. Enter the password you created. If you
did not create a new password, use the default password admin. (You can set
a new password from the Administration > Management screen.) Click OK to
continue.
NOTE
If the password request screen does not appear, wait two minutes
and try again.
Advanced Configuration
75


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Linksys WUMC710 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Linksys WUMC710 in the language / languages: All languages as an attachment in your email.

The manual is 7,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info