602190
27
Zoom out
Zoom in
Previous page
1/80
Next page
20
Chapter 5: Configuring the ADSL Gateway
The Setup Tab
ADSL Gateway with 4-Port Switch
Advanced Routing
The Advanced Routing screen allows you to configure the dynamic routing and static routing settings.
Advanced Routing
Dynamic Routing. With Dynamic Routing you can enable the Gateway to automatically adjust to physical
changes in the network’s layout. The Gateway, using the RIP protocol, determines the network packets’ route
based on the fewest number of hops between the source and the destination. The RIP protocol regularly
broadcasts routing information to other Gateways on the network. To enable RIP, click Enabled. To disable
RIP, click Disabled.
Receive RIP Version. To receive RIP messages, select the protocol you want: RIP1 or RIP2. If you don’t want
to receive RIP messages, select None.
Transmit RIP Version. To transmit RIP messages, select the protocol you want: RIP1, RIP1-Compatible, or
RIP2. If you don’t want to transmit RIP messages, select None.
Static Routing
If the Gateway is connected to more than one network, it may be necessary to set up a static route between
them. A static route is a pre-determined pathway that network information must travel to reach a specific host or
network. To create a static route, change the following settings:
Select Entry. Select the number of the static route from the drop-down menu. The Gateway supports up to 20
static route entries. If you need to delete a route, after selecting the entry, click the Delete Entry button.
Destination IP Address. The Destination IP Address is the address of the remote network or host to which you
want to assign a static route. Enter the IP address of the host for which you wish to create a static route. If you
are building a route to an entire network, be sure that the network portion of the IP address is set to 0.
Subnet Mask. The Subnet Mask (also known as the Network Mask) determines which portion of an IP address
is the network portion, and which portion is the host portion.
Gateway. This IP address should be the IP address of the gateway device that allows for contact between the
Gateway and the remote network or host.
Hop Count. This determines the maximum number of steps between network nodes that data packets will
travel. A node is any router in the path to the remote network.
Interface. Select LAN or Internet, depending on the location of the static route’s final destination.
F
i
g
u
r
e
5
-
1
1
:
S
e
t
u
p
T
a
b
-
A
d
v
a
n
c
e
d
R
o
u
t
i
n
g
node: a network junction or connection point,
typically a computer or work station
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Linksys AG041 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Linksys AG041 in the language / languages: English as an attachment in your email.

The manual is 1,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info