693631
75
Zoom out
Zoom in
Previous page
1/82
Next page
POD Farm 2 Basic User Guide - Standalone Operation
4•4
Main Control Bar
The Main Control Bar is always shown at the top of the POD Farm 2 window, and includes a number
of global controls and “View” buttons. The controls are the same here as described in the Plug-In
chapter’s “1 - Main Control Bar” on page 3•4, with the exception of the Input & Output controls,
described as follows.
Input Meter Master Output Control
The Main Control Bar
Input Meter - The meter provides peak display with clip indicators to measure the level of your
selected Source Input(s).
You’ll see a Mono or Stereo meter here, depending on if you’ve selected either one or two Input
Sources for Tone A & B (see “Mixer View” on page 4•5).
The “colorized” stereo level meters provide the following input level information:
The green to yellow range of the meters indicates up to -18 dB (instrument level).
The yellow range of the meters indicates from -18 dB to 0 dB (full scale).
The red “clip indicators” light up if the input exceeds 0 dB. Clipping should always be
avoided!
*Important! Setting your input levels before they are fed into POD Farm 2 is critical for optimizing your
audio signal quality. Here are some helpful tips concerning Input levels:
• Some POD Farm 2 models are calibrated to receive an “instrument level” audio signal (-18 dB).
Therefore, when any of these models exist in your Tone path, use your instrument or input
device’s volume or gain controls to optimize the input level coming into POD Farm 2 so that
the Input meters remain in the higher end of the green range. These “instrument level” models
include all those in the following categories:
• Guitar Amps
• Bass Amps
• Distortions
• Filters
• Dynamics (excluding the “Compressor “ model, which receives up to full scale input)
• When your Tone path does not include any of the above instrument level models, then the Input
level can be as high as full scale.
Master Output Control - Use the knob and meter here to optimize the POD Farm 2 Tone A & B
monitor output level.
TIP: The Master Output knob & meter control only the ToneDirect Monitoring output of POD Farm 2
(the signal you hear from your Line 6 hardware Main & Headphone outputs). Use the Mixer View’s Record
Send faders (see page 4•6) to independently control the levels fed to your DAW software for recording!
If you have a Dual Tone signal path, this controls the total mix of Tones A & B.
75


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Line 6 POD Farm 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Line 6 POD Farm 2 in the language / languages: English as an attachment in your email.

The manual is 4,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Line 6 POD Farm 2

Line 6 POD Farm 2 User Manual - Dutch - 82 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info