693634
14
Zoom out
Zoom in
Previous page
1/16
Next page
The following table describes how the dierent processing Blocks are
indicated on the device while in Live Edit Mode.
BLOCK TYPE ABBREVIATION
IN LCD SCREEN
FOOTSWITCH LED
COLOR
Drives & Dynamics
DRV
Yellow
Compressor
CMP
Filters, Synths & Pitch
SYN
Purple
Modulation
MOD
Blue
Delays
DLY
Green
Reverb
REV
Orange
FX Loop
FXL
Turquoise
Looper
LPR
White
Amp
AMP
Red
Speaker Cabinet
CAB
Preset EQ
PEQ
Select a Block to Edit: Press the footswitch assigned to the Block
that you wish to edit. You'll see the LCD rst show the full name
of the selected Block's current model, and and then display the
current model's rst parameter - now you're ready for editing.
Digital Delay
DLY:Time 430ms
First the full model name is shown, then its rst editable parameter
To Edit the Current Parameter: Move the device's Expression
Pedal or Master Volume Knob to adjust the editable value. Or,
press the Bank Up or Bank Down footswitches to adjust the
value in ne increments. You'll see the parameter's current value
indicated in the LCD and by the Master Volume knob's LED ring.
To Edit a Dierent Parameter: Repeatedly press the same
footswitch to cycle through all editable parameters for the current
model.
You can adjust the value for one parameter, then simply tap
the footswitch again to edit another. Your edited values are
all retained until you exit Live Edit Mode, at which point you
choose to Save or discard them.
Note that Model Select option allows you to choose a dierent
model type, which then becomes assigned to the current
footswitch.
To Edit a Dierent Block: Press any other FS1FS5 or AD
footswitch to access its assigned block. You'll then be able to edit
its current model, or load a dierent model, using the same steps
mentioned above.
To Exit Live Edit Mode: Press both the Bank Up and
Bank Down footswitches simultaneously.
Be sure to Save to retain your edited settings. See the previous
6. Preset & Bank Select Footswitches section for details on Save
Mode.
NOTE: The device's Tone, Reverb & FX knobs and the Tap Tempo
footswitch all continue to function while in Live Edit Mode.
Factory Reset & Pedal Calibration
Performing a Factory Reset restores the Firehawk FX to the original
factory settings and Presets. Be sure to use the Firehawk Remote app
to back up your customized Presets before performing a Factory
Reset! After performing a Factory Reset, it is recommended that you
next perform the Pedal Calibration for proper Pedal operation.
Factory Reset: Simultaneously press and hold the Master Volume
Knob and the TAP footswitch as you power on the unit.
Pedal Calibration: Power O your Firehawk FX device, then press
and hold footswitch A while powering On the unit. Follow the steps
in the LCD screen to calibrate the on-board Expression Pedal.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Line 6 Firehawk FX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Line 6 Firehawk FX in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Line 6 Firehawk FX

Line 6 Firehawk FX User Manual - Dutch - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info