693634
13
Zoom out
Zoom in
Previous page
1/16
Next page
To reverse playback of your loop: Press and hold the Looper switch
for ~2 seconds while the loop is playing. Press and hold the Looper
switch again to revert back to non-reverse playback.
To stop Looper playback: Double-tap the Looper footswitch. The
LED stops ashing and turns bright white, indicating a loop is stored in
memory. Press the Looper footswitch again to restart playback of the
stored loop.
To delete the recorded loop and start from scratch: Stop the Looper
and press and hold the footswitch for ~2 seconds. The LED returns to
dim white, indicating there is no loop in memory.
Output Modes
The OUTPUT MODE switch found on the Firehawk FX rear panel
cleverly congures the audio signals sent out the XLR and 1/4-inch
outputs to optimize them for your setup:
Line Out Mode optimizes the guitar sound for direct recording and
full-range monitoring. The signal is at line level and simulates the
sound of a mic’d amp out of both the XLR and 1/4” outputs.
Amp Out Mode is very dierent in that the guitar sound is
optimized for connecting into the front of a guitar amp. The signal
is at instrument level and is not appropriate to monitor through
headphones or a full range system, therefore, the guitar signal is
only present at the 1/4” outputs in this mode.
Because Bluetooth
®
streamed audio does not typically sound best
playing through a guitar amp, the 1/4” outs carry only the guitar
signal when in Amp Out Mode – Bluetooth
®
audio is only present
at the XLR and Headphone outs in this mode.
As shown in the following table, the guitar audio signal is optimized for
a full range system versus for a guitar amp, and the level for each signal
also changes with the LINE and AMP Output Mode settings.
LINE MODE AMP MODE
XLR Output
Audio
Guitar Tone is Studio/Direct optimized
Includes Bluetooth streamed playback
Bluetooth streamed playback
only
XLR Output
Level
8.219 dBu / 6.0 dBv 8.219 dBu / 6.0 dBv
1/4” Output
Audio
Guitar Tone is Studio/Direct optimized
Includes Bluetooth streamed playback
Guitar Tone only - Amplifier
optimized
1/4” Output
Level
Line level Instrument level
LINE vs. AMP Mode - Audio signal type and level sent to outputs
NOTE: In either OUTPUT MODE setting, the PHONES output always
receives the same audio as the XLR outputs.
Live Edit Mode
The Live Edit Mode allows you quick access to the individual FX
parameters on the Firehawk FX device as an alternative to using the
Firehawk Remote app for adjusting your FX settings. The steps are as
follows.
Editing FX Parameters
Enter Live Edit Mode by simultaneously pressing both the
Bank Up and Bank Down footswitches. The two rows of
footswitches, FS1FS5 and AD, will alternate ashing. You'll see
abbreviations for the processing blocks accessible for each row of
footswitches are displayed in the LCD to help you choose what you
want to edit. As indicated, the FX and Looper blocks are accessed
via FS1FS5 and the Amp, Cab & EQ are accessed via AC.
DRV REV MOD DLY LPR AMP CAB PEQ
The LCD displays the editable blocks for the row of ashing
footswitches
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Line 6 Firehawk FX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Line 6 Firehawk FX in the language / languages: English as an attachment in your email.

The manual is 1,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Line 6 Firehawk FX

Line 6 Firehawk FX User Manual - Dutch - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info