Manual Liftmaster LM60 (page 21 of 288) (All languages)

633114

Zoom out

Zoom in

1/288

en 05/13

Installation of photocells

(Optional accessory)

After installing and adjusting the door opener, photocells can be installed.

The installation instructions are included with the photocells.

The optional photocells ensure that the door is open, or remains

open, if people, especially young children, are in the door area.

By means of the photocells, a closing door is opened or an open door is

obstructed from closing, if a person located in the door area interrupts the

sensor beam.

Photocells are particularly recommended for families with young children.

Connecting the opener

Connect opener in accordance with local rules and regulations to a

properly installed wall socket.

NOTE:

When the opener is switched on, the operator light is also turned on

for 2.5 minutes.

Program opener and test

The door opener should only be used if the operator can see the

entire door area and is assured that it is free of obstacles

and the

door opener is set correctly. No one may pass through

the door while it is moving. Before the first opening operation, check that all

the facilities that are not needed are turned off. Remove all mounting aids

and tools from the pivot area of the door.

Setting the Limits

Travel limits regulate the points at which the door will stop when moving up

or down. Follow the steps below to set the limits.

This operator is equipped with a two speed system that is automatically set

by the software. Canopy or 1-piece garage doors will automatically run in

slow speed to insure a safe operation according regulatory. Doors traveling

shorter than 190 cm will run automatically slow.

INTRODUCTION

Your garage door opener is designed with electronic controls to make setup

and adjustments easy. The adjustments allow you to program where the

door will stop in the open (UP) and close (DOWN) position. The electronic

controls sense the amount of force required to open and close the door.

The force is adjusted automatically when you program the travel.

NOTE: If anything interferes with the door’s upward travel it will stop. If

anything interferes with the door’s downward travel, it will reverse.

To watch a short instructional video on programming your new garage door

opener use your smartphone to read the Code on this manuals back side

or visit www.liftmaster.eu.

PROGRAMMING BUTTONS

The programming buttons are located under a removable cover on the

back side of the garage door opener (see fig24).

1. Press and hold the square Adjustment Button until the UP Button begins

to flash.

2. Press and hold the UP Button until the door is in the desired UP position.

NOTE: The UP and DOWN Buttons can be used to move the door up

and down as needed.

3. Once the door is in the desired UP position press and release the

Adjustment Button. The garage door opener lights will flash and

the DOWN Button will begin to flash.

4. Press and hold the DOWN Button until the door is in the desired DOWN

position. Make sure the rail does not bend. NOTE: The UP and DOWN

Buttons can be used to move the door up and down as needed.

5. Once the door is in the desired DOWN position press and release the

Adjustment Button. The garage door opener lights will flash and the UP

Button will begin to flash.

6. Press and release the UP Button. When the door travels to the pro

grammed UP position, the DOWN Button will begin to flash.

Note: IF the door does not travel to the UP position the travel limit

programming failed. Begin again with step1.

If door travel is too short please refer to section 33 ”Frequently Asked

Questions”.

7. Press and release the DOWN Button. The door will travel to the

programmed DOWN position. Programming is complete.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Liftmaster LM60 in the language / languages: All languages as an attachment in your email.

The manual is 7,94 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Liftmaster LM60 Manual

Product: