600889
16
Zoom out
Zoom in
Previous page
1/36
Next page
16
Ground
Tab
Green Ground
Screw
Ground Wire
Black Wire
From Power
Cord
White Wire
From Power
Cord
Flexible
Conduit
90˚ Connector
Green Wire
White Wire
Black Wire
BACK VIEW
Connect Power
8
Installation
OPTION B: PERMANENT WIRING
CONNECTION
If permanent wiring is required by your local
code, refer to the following procedure.
To make a permanent connection through
the 7/8 inch hole in the back of the garage
door opener (according to local code):
1. Be sure power is NOT connected to
the opener, and disconnect power to
circuit.
2. Remove the garage door opener from
the torsion bar, remove cover screws
and set the cover aside.
3. Remove the attached green ground
terminal.
4. Cut black and white wires and strip
away 1/2 inch (1.3 cm) of insulation,
3 inch (7.6 cm) before spade terminals.
5. Remove the power cord from the
garage door opener.
6. Install a 90° conduit or fl ex cable
adapter to the 7/8 inch hole. Reinstall
garage door opener to torsion bar.
7. Run wires through conduit, cut to
proper length and strip insulation.
8. Attach with wire nuts provided.
9. Properly secure wire under plastic ties
so that wire does not come in contact
with moving parts.
10. Reinstall the cover.
To avoid installation diffi culties, do not run
the garage door opener at this time.
To reduce the risk of electric shock, your
garage door opener has a grounding type
plug with a third grounding pin. This plug
will only fi t into a grounding type outlet. If
the plug doesn’t fi t into the outlet you have,
contact a qualifi ed electrician to install the
proper outlet.
There are two options for connecting
power:
OPTION A: TYPICAL WIRING
1. Plug in the garage door opener into a
grounded outlet.
2. DO NOT run garage door opener at this
time.
To prevent possible SERIOUS INJURY or DEATH from electrocution or fi re:
Be sure power is NOT connected to the opener, and disconnect power to circuit
BEFORE removing cover to establish permanent wiring connection.
Garage door installation and wiring MUST be in compliance with ALL local electrical
and building codes.
NEVER use an extension cord, 2-wire adapter or change plug in ANY way to make it
t outlet. Be sure the opener is grounded.
RIGHT
IMPORTANT NOTE: The model 580LM Alternate
Power Supply may be installed if an outlet is not
located near the garage door opener. MyQ
®
light
controls will continue to work however all other
MyQ
®
devices and TTC WILL NOT work if using
the Model 580LM Alternate Power Supply. If
you would like to use these features, contact an
electrician to install an outlet near to the garage
door opener.
WRONG
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liftmaster 8500 Elite at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liftmaster 8500 Elite in the language / languages: English as an attachment in your email.

The manual is 5,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info