552453
13
Zoom out
Zoom in
Previous page
1/21
Next page
12
4. Seat Sliding Tube, Back/Seat Support Bracket, and Handlebar Installation
Remove eight Ø8 Washers (36) and eight M8x15 Bolts (72) from the Seat Sliding Tube (52).
Remove bolts with the S5 Allen Wrench provided.
Insert the Seat Sliding Tube (52) into the Bushings (61) of the Rear Main Frame (46).
Attach the Back and Seat Support Bracket (53) onto the Seat Sliding Tube (52) with eight
Ø8 Washers (36) and eight M8x15 Bolts (72) that were removed. Tighten bolts with the S5
Allen Wrench provided.
Adjust the seat position and align knob holes. Insert the Round Knob (60) and Triangle
Knob (23) into knob holes. Turn the Round Knob (60) and Triangle Knob (23) in the
clockwise direction to tighten.
Attach the Handlebar (68) onto the Back and Seat Support Bracket (53) with two M8x45
Bolts (57), two Ø8xØ20x2 Big Curve Washers (4), two Ø8 Washers (36), and M8 Cap Nuts
(3). Tighten bolts and cap nuts with the S6 Allen Wrench and Multi Hex Tool with Phillips
Screwdriver provided.
Connect the Hand Pulse Sensor Wires (56) from the Handlebar (68) to the Middle Section
Hand Pulse Sensor Wires (44) from the Rear Main Frame (46).
Adjusting the Seat Forward or Back
Turn the Triangle Knob (23) to loosen the Seat Sliding Tube (52). Turn the Round Knob
(60) in a counterclockwise direction until it can be pulled out. Pull out the Round Knob (60)
and then slide the Back and Seat Support Bracket (53) back or forth direction to the suitable
position. Lock the Back and Seat Support Bracket (53) in place by releasing the Round
Knob (60) and sliding the Back and Seat Support Bracket (53) back or forth slightly until the
Round Knob (60) "pops" down into the hole of the Seat Sliding Tube (52). For added safety,
tighten the Triangle Knob (23) and Round Knob (60) in a clockwise direction.
NOTE: When adjusting the seat back or forth direction, the maximum insert depth
mark line cannot over than the edge of Bushing (61).
Tool:
Allen Wrench S5
Multi Hex Tool with Phillips Screwdriver
S8, S13, S14, S15
57
3
36
52
72
36
72
36
36
72
72
68
4
53
56
23
60
44
46
61
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for LifeGear Formula Magnetic Recumbent Bike 26580 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of LifeGear Formula Magnetic Recumbent Bike 26580 in the language / languages: English as an attachment in your email.

The manual is 1,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info