804841

Liebherr K2340 Manual

7
Zoom out
Zoom in
Previous page
1/14
Next page
CAUTION
Risk of injury if the door tips!
uTake good hold of the door.
uSet down the door carefully.
uUnscrew top bearing block Fig. 6 (3) (2x Torx® 20)
Fig. 6 (4) and lift off in upward direction.
uLift out the door and set aside.
4.3.2 Relocating the bearing components
Fig. 7
uUnscrew fastening screws Fig. 7 (21).
uRemove the lower bearing block Fig. 7 (23), complete with
bearing bolt Fig. 7 (24), washer Fig. 7 (26) and adjustable
foot Fig. 7 (22).
uUnscrew the bearing bolt Fig. 7 (24), complete with
washer Fig. 7 (26), re-locate it into the mounting hole on
the opposite side of the bearing block and tighten again.
uCarefully remove the cover plate Fig. 7 (25) and re-locate
it to the other side.
uScrew on the lower bearing block Fig. 7 (23), complete
with bearing bolt Fig. 7 (24), washer Fig. 7 (26) and adjust‐
able foot Fig. 7 (22) to the new hinge side, with the help
of a cordless screwdriver if necessary, and tighten (with
4 Nm) once again.
4.3.3 Transferring the handle
uLift the stopper Fig. 8 (30) out of the door bearing bush
and transfer it.
Fig. 8
uDetach door handle Fig. 8 (31), stoppers Fig. 8 (32) and
pressure plates Fig. 8 (33) plates and transfer to the
opposite side
uWhen fitting the pressure plates at the opposite side, pay
attention that they engage properly.
4.3.4 Fitting the lower door
uLower the door from above onto the bearing bolt
Fig. 7 (24).
uClose the door.
uInstall the upper bearing block Fig. 6 (3) on the new hinge
side and in the door.
uScrew in the upper bearing block tightly (with 4 Nm)
(2x Torx® 20) Fig. 6 (4). Use a cordless screwdriver if
necessary.
uSlide on the cover Fig. 6 (1) on the opposite side from the
outside and snap it into place.
uSlide on the cover Fig. 6 (2) on the opposite side from
above until it snaps into place.
uUnscrew the adjustable foot Fig. 7 (22) on the lower
bearing block Fig. 7 (23) until it touches the floor.
Fig. 9
uInsert the spacer Fig. 9 (13) back under the right-hand
side of the door, as this is important for the stability of
the appliance.
WARNING
Danger of injury due to door falling out!
If the bearing parts are not screwed on tightly enough, the
door may fall out. This can result in serious injuries. In
addition, the door may not close with the result that the
appliance does not cool properly.
uScrew the bearing brackets on firmly with 4 Nm.
uCheck all screws and retighten them if necessary.
Putting into operation
* Depending on model and options 7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liebherr K2340 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr K2340 in the language / languages: English as an attachment in your email.

The manual is 1.07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr K2340

Liebherr K2340 User Manual - German - 14 pages

Liebherr K2340 User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info