Manual Liebherr K 2814 (page 7 of 14) (English)

597453

Zoom out

Zoom in

1/14

Detach door handle

Fig. 10 (31)

, stoppers

Fig. 10 (32)

and

pressure plates

Fig. 10 (33)

plates and transfer to the oppo-

site side

When fitting the pressure plates at the opposite side, pay

attention that they engage properly.

4.3.5 Fitting the lower door

Lower the door from above onto the bearing bolt

Fig. 9 (24)

Close the door.

Install the upper bearing block

Fig. 6 (3)

on the new hinge

side and in the door.

Screw in the upper bearing block tightly (with 4 Nm) (2x

Torx® 25)

Fig. 6 (4)

. Use a cordless screwdriver if

necessary.

Slide on the cover

Fig. 6 (1)

on the opposite side from the

outside and snap it into place.

Slide on the cover

Fig. 6 (2)

on the opposite side from above

until it snaps into place.

Unscrew the adjustable foot

Fig. 9 (22)

on the lower bearing

block

Fig. 9 (23)

until it touches the floor.

Fig. 11

Insert the spacer

Fig. 11 (13)

back under the right-hand side

of the door, as this is important for the stability of the appli-

ance.

WARNING

Risk of injury due to the door dropping out!

If the bearing parts are not screwed into place firmly enough,

the door may drop out. This may lead to severe injuries. What is

more, the door may not close and therefore the appliance may

fail to cool properly.

Screw the turn hinges firmly into place with 4 Nm.

Check all of the screws and retighten if necessary.

4.4 Insertion into a row of kitchen units

Fig. 12

(1) Stack cabinet (3) Kitchen cabinet

(2) Appliance (4) Wall

For appliances supplied with wall spacers, the measurement

increases by 35 mm (see 4.2) .

The appliance can be built into kitchen units. A top cupboard

Fig. 12 (2)

can be added above the appliance in order to bring

the appliance

Fig. 12 (1)

up to the height of the fitted kitchen

units.

When installing with kitchen units (max. depth 580 mm), the

appliance can be positioned directly next to the kitchen cabinet

Fig. 12 (3)

. The appliance will project by 34 mm

at the sides

and 50 mm

in the centre of the appliance in relation to the

kitchen cabinet front.

NOTICE

Danger of overheating due to insufficient air ventilation!

The compressor may be damaged if there is insufficient air

ventilation.

Take care to ensure adequate air ventilation.

Observe the ventilation requirements.

Ventilation requirements:

At the back of the stack cabinet there has to be a ventilation

duct of at least 50 mm depth throughout the width of the

stack cabinet.

The cross section of the ventilation gap below the ceiling

must be at least 300 cm

the larger the ventilation space, the more energy-saving the

appliance is in operation.

If the appliance is installed with the hinges next to a wall

Fig. 12 (4)

, the distance between appliance and wall has to be

at least 40 mm. This corresponds to the projection of the

handle when the door is open.

Putting into operation

* Depending on model and options 7

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr K 2814 in the language / languages: English as an attachment in your email.

The manual is 0,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr K 2814

Liebherr K 2814 User Manual - German - 14 pages

Liebherr K 2814 User Manual - Dutch - 14 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Liebherr K 2814 Manual

Product: