Manual Liebherr GP 2033-20 (page 6 of 14) (English)

710287

Zoom out

Zoom in

1/14

Note

Clean the appliance (see 6.2 Cleaning the appliance) .

If the appliance is installed in a very damp environment,

condensate may form on the outside of the appliance.

Always see to good ventilation at the installation site.

4.3 Changing over the door hinges

You can change over the door hinges if necessary.

Ensure that the following tools are to hand:

Torx 25

Torx 15

Open-ended spanner size 10

Screwdriver

Open-ended spanner included in supply package

Second person for fitting work, if needed

CAUTION

Risk of injury if the door tips!

Take good hold of the door.

Set down the door carefully.

Unscrew the securing screw on

the bottom right turn hinge.

Open the door.

Hold the door on the handle side

and at the bottom and lift it.

The bearing pin

Fig. 5 (21)

should

come out of the turn hinge

Fig. 6 (2)

If the bearing bolt

Fig. 5 (21)

doesn't undo press it out from

underneath.

Fig. 5

Swing door out at the bottom and remove it.

Fig. 6

Unscrew the turn hinge

Fig. 6 (2)

Unscrew the bearing element,

Fig. 6 (3)

transfer it to the

opposite location hole of the turn hinge and screw it firmly

into place.

Take the stopper

Fig. 6 (4)

out of the turn hinge and transfer

it to the receiving hole on the opposite side of the turn hinge.

Carefully lift off the cover

Fig. 6 (5)

on the handle side.

Undo the screw

Fig. 6 (6)

and transfer it to the opposite side.

Put the cover

Fig. 6 (5)

back on.

Screw the turn hinge

Fig. 6 (2)

firmly into place on the new

hinge side (with 4 Nm), possibly using a power screwdriver.

Fig. 7

At the top, use a screwdriver to unclip cover

Fig. 7 (7)

and

cover

Fig. 7 (8)

at the front, and remove by pulling out and

down.

Unscrew the bearing pin

Fig. 7 (9)

and screw it firmly into

place on the opposite side (with 4 Nm).

Refit the cover

Fig. 7 (7)

on the side of the bearing pin: insert

at the back, snap in at the front.

Fit the cover

Fig. 7 (8)

on the opposite side: insert at the

back, snap in at the front.

Fig. 8

Lift the stopper

Fig. 8 (12)

out of the door bearing bush and

transfer it.

Detach door handle, stoppers

Fig. 8 (10)

and pressure

plates

Fig. 8 (11)

and transfer to the opposite side.

When mounting the pressure plates, make sure they snap

into place properly.

Transfer the spring clamp

Fig. 9 (20)

: Depress the

latch nose and pull the

spring clamp off over it.

Slide the spring clamp into

place on the new hinge

side until it clicks into

place.

Pull the bearing pin

Fig. 9 (21)

out of the door

bush and transfer it to the

opposite side together with

the washer. The latch nose

must point to the inner side

of the door, the notch to

the outer side.

Fig. 9

Hang the door on the bearing pin

Fig. 7 (9)

at the top.

Swing the door in at the bottom and insert the bearing pin

Fig. 9 (21)

into the turn hinge. If necessary, turn the bearing

pin until it snaps into place.

Insert the securing screw

Fig. 5 (1)

at the bottom into the

bearing pin and tighten it (with 4 Nm).

If necessary, align the door flush with the appliance housing

using the two slots in the turn hinge. To do so, unscrew the

middle screw.

Putting into operation

6 * Depending on model and options

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr GP 2033-20 in the language / languages: English as an attachment in your email.

The manual is 0,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr GP 2033-20

Liebherr GP 2033-20 User Manual - Dutch - 14 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Liebherr GP 2033-20 Manual

Product: