805276

Liebherr GN1066 Manual

7
Zoom out
Zoom in
Previous page
1/14
Next page
If you are integrating the appliance into a kitchen unit (max.
depth 580 mm) you can install it right next to the kitchen
cabinet Fig. 5 (3). The appliance measures 34 mm x at the
side and 50 mm x at the centre in relation to the front of the
kitchen cabinet.
NOTICE
Danger of overheating due to insufficient air ventilation!
The compressor may be damaged if there is insufficient air
ventilation.
uTake care to ensure adequate air ventilation.
uObserve the ventilation requirements.
Ventilation requirements:
-At the back of the top cabinet, there must be an air outlet
shaft at least 50 mm deep spanning the entire width.
-The ventilation above must be at least 300 cm2.
-The wider the ventilation clearance, the more efficiently
the appliance will run.
If you are installing the appliance with the hinges next to a
wall Fig. 5 (4), the distance between the appliance and the
wall must be at least 40 mm. This is how far the handle
protrudes when the door is open.
4.5 Disposing of packaging
WARNING
Danger of suffocation due to packing material and plastic
film!
uDo not allow children to play with packing material.
The packaging is made of recyclable materials:
-corrugated board/cardboard
-expanded polystyrene parts
-polythene bags and sheets
-polypropylene straps
-nailed wooden frame with polyethylene panel*
uTake the packaging material to an official collecting
point.
4.6 Connecting the appliance
NOTICE
Failure to connect properly
Damage to the electronics.
uDo not connect the appliance to a stand-alone inverter,
e.g. solar power systems and petrol generators.
uDo not use an energy saving plug.
WARNING
Failure to connect properly
Fire hazard.
uDo not use an extension cable.
uDo not use distributor blocks.
The type of current (alternating current) and voltage at the
installation site have to conform with the data on the type
plate (see 1 Appliance at a glance) .
The socket must be properly earthed and fused. The tripping
current for the fuse must be between 10 A and 16 A.
The socket must be easily accessible so that the appliance
can be quickly disconnected from the supply in an emer‐
gency. It must be outside the area of the rear of the appli‐
ance.
uCheck the electrical connection.
uPlug in the power plug.
4.7 Switching on the appliance
uPress the On/Off button Fig. 3 (1).
wThe appliance is switched on. The temperature display
and Alarm symbol Fig. 3 (6) flash until the temperature is
cold enough.
wIf “DEMO” is displayed, demo mode is activated. Please
contact the after sales service.
5 Control
5.1 Brightness of the temperature
display
You can adjust the brightness of the temperature display to
the light conditions of the room in which the appliance is
installed.
5.1.1 Setting the brightness
The brightness is adjustable between h 0 (minimum bright‐
ness) and h 5 (maximum brightness).
uActivate setting mode by pressing the SuperFrost button,
Fig. 3 (4), for approx. 5 sec.
wThe Menu symbol is shown on the display, Fig. 3 (7).
wc flashes on the display.
uUse the adjustment button, Fig. 3 (2), to select h.
uBriefly confirm with the SuperFrost button, Fig. 3 (4).
wThe display shows the last set brightness
value.
uUse the adjustment button, Fig. 3 (2), to set the desired
value from h 0 to h 5.
uBriefly confirm the newly set brightness value with the
SuperFrost button Fig. 3 (4).
wh flashes on the display.
wThe brightness is set.
uAfter making the change, deactivate setting mode: Press
the On/Off button Fig. 3 (1) once.
wThe temperature display shows the temperature again.
If setting mode is already activated but you would like to
keep the old brightness value setting:
uPress the On/Off button Fig. 3 (1)twice to deactivate
setting mode.
wThe temperature display shows the temperature again.
5.2 Child proofing
The child-proofing function enables you to make
sure that the appliance is not inadvertently
switched off by playing children.
5.2.1 Setting the child lock
To switch on the function:
uActivate setting mode: press the SuperFrost button
Fig. 3 (4) for approx. 5 seconds.
wThe Menu symbol Fig. 3 (7) is shown on the display.
wc flashes on the display.
uBriefly confirm with the SuperFrost button, Fig. 3 (4).
wc1 appears in the display.
uBriefly confirm with the SuperFrost button, Fig. 3 (4).
Control
* Depending on model and options 7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liebherr GN1066 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr GN1066 in the language / languages: English as an attachment in your email.

The manual is 1.49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr GN1066

Liebherr GN1066 User Manual - German - 14 pages

Liebherr GN1066 User Manual - Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info