715463
7
Zoom out
Zoom in
Previous page
1/18
Next page
EN
Power failure/FrostControl display
If the LED comes on on the control panel, this means that the
freezer temperature has risen too high during the last few hours
or days due to a power failure.
If you touch the ALARM icon now, the highest temperature
registered during the power failure will be displayed.
Check the quality of the food and its suitability for consumption
in case it has become too warm or even defrosted.
The highest temperature will appear for appox. 1 minute. After
that, the actual temperature in the freezer will re-appear.
The display can be switched off by touching the ALARM icon.
Audible warning signal
The appliance is equipped with an alarm function.
Audible door alarm
If an appliance door is left open for more than 60 seconds,
the audible warning signal will sound. Touch the ALARM
icon to cancel the alarm. The alarm switches back to
standby when the door is shut.
Audible/visual temperature alarm
It sounds when it is not cold enough in the freezer compartment.
The temperature display and the LED will also flash.
The audible warning device is switched off by touching
the ALARM icon. The temperature display will continue
to flash until the cause of the alarm has been rectified.
This can be caused by:
the freezer door being left open for a long time, allowing warm
ambient air to enter;
a long power failure;
a fault in the appliance.
In each case, make sure food has not thawed or perished.
SuperCool
Touching the SuperCool icon switches the refrigerator compart-
ment to maximum cooling. It is recommended particularly if you
wish to cool large quantities of food, drinks, freshly baked goods
or meals rapidly.
Switching on: Touch the SuperCool icon briefly so that
the LED comes on. The refrigerator temperature will
drop to its lowest value.
Note: The SuperCool function uses slightly more energy. After
approximately six hours, however, the refrigerator switches back
automatically to normal energy-saving operation. If required, the
SuperCool function can be switched off sooner.
Switching off: Touch the SuperCool icon again until the LED
goes out.
Setup mode
The following functions can be activated in setup mode:
= Sabbath mode
= Child lock
= Confirm water filter change
= Ice maker vacation state
= Water quantity for ice cube tray
= Set BioFresh temperature
= Display brightness
= Door gasket heating control
=Confirm dust filter cleaning
Activating setup mode
Touch the SuperFrost icon for five seconds.
- The SuperFrost LED comes on for 5 seconds,
- after 5 seconds will flash in the display.
The appliance is in setup mode now.
You can select the setup mode functions by touching
the freezer compartment temperature setting icons.
Note
In setup mode the display will flash continuously.
Exiting setup mode
Touch the freezer compartment On/Off icon
The appliance will change back to normal operation.
23
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Liebherr ECBN 6256 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr ECBN 6256 in the language / languages: English as an attachment in your email.

The manual is 2.18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr ECBN 6256

Liebherr ECBN 6256 User Manual - German - 12 pages

Liebherr ECBN 6256 Installation Guide - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info