Manual Liebherr cbnes 5067 422l (page 7 of 26) (English)

348146

Zoom out

Zoom in

1/26

Always stand the appliance backed directly to the wall using

the enclosed wall spacers (see below).

The appliance may be moved only when it is empty.

Do not install the appliance without assistance.

The more R 600a refrigerant there is in the appliance, the

larger the room in which the appliance is standing needs to

be. In rooms that are too small, a flammable mix of gas and

air may be created if there is a leak. According to the EN

378 standard, every 11 g of R 600a refrigerant requires at

least 1 m

space in the room for the appliance. The amount

of refrigerant in your appliance is on the type plate inside the

appliance.

Detach the connecting cable from the rear of the appliance,

removing the cable holder at the same time because other-

wise there will be vibratory noise!

Remove the protective film from the outside of the appli-

ance.

NOTICE

The stainless steel doors are provided with a high-quality

surface coating and must not be treated using the accompa-

nying care product.

Otherwise the surface coating will be affected.

Wipe the coated door surfaces using a soft, clean cloth

only.

Apply a stainless steel cleaner only to the stainless steel

side walls evenly, wiping with the grain. Subsequent

cleaning becomes easier as a result.

Wipe side walls with a paint finish using a soft, clean

cloth only.

Remove the protective film from the decorative trims and

drawer fronts.

Remove all transit supports.

The spacers supplied with some appliances must be used to

achieve the stated energy consumption. These will extend the

depth of the appliance by approx. 35 mm. The appliance is fully

functional if the spacers are not used, but does have a slightly

higher energy consumption.

In the case of an appliance with

enclosed wall spacers, mount the

wall spacers on the back of the

appliance at the top left and right.

Dispose of packaging material (see 4.6) .

Align the appliance so that it

stands firmly and on a level by

applying the accompanying

spanner to the adjustable-

height feet (A) and using a

spirit level.

Then support the door: Extend

the adjustable foot at the turn

hinge (B) until it rests on the

floor and then make a further

90° turn.

Note

Clean the appliance (see 6.2) .

If the appliance is installed in a very damp environment,

condensate may form on the outside of the appliance.

Always see to good ventilation at the installation site.

4.3 Changing over the door hinges

You can change over the door hinges if necessary.

Ensure that the following tools are to hand:

Torx® 25

Torx® 15

Screwdriver

Cordless screwdriver, if necessary

Second person for fitting work, if needed

4.3.1 Detaching the upper soft stop mecha-

nism*

For appliances with soft stop mechanism start with this item.

For appliances without soft stop mechanism start with item

(see 4.3.2) .

Fig. 4

Open the upper door.

NOTICE

Risk of damage!

If the door seal is damaged, the door may fail to close properly

and the cooling will be inadequate.

Do not damage the door seal with the screwdriver!

Disengage and remove the faceplate

Fig. 4 (1)

using a flat-

blade screwdriver.

The faceplate is attached over the soft stop bracket.

Fig. 5

Push the faceplate over the soft stop bracket

Fig. 5 (4)

in the

direction of the appliance.

Snap the safety lock

Fig. 5 (2)

into the oblong hole.

The safety lock prevents the hinge from snap-closing.

Using a screwdriver, disengage the cover on the hinge side

Fig. 5 (5)

as far as the first detent.

The pin becomes visible.

Press the pin

Fig. 5 (3)

out from underneath.

Press the soft stop bracket

Fig. 5 (4)

towards the door.

Fully detach the cover on the hinge side

Fig. 5 (5)

and

remove it.

Putting into operation

* Depending on model and options 7

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Liebherr cbnes 5067 422l in the language / languages: English as an attachment in your email.

The manual is 0,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Liebherr cbnes 5067 422l

Liebherr cbnes 5067 422l User Manual - German - 26 pages

Liebherr cbnes 5067 422l User Manual - Dutch - 13 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Liebherr cbnes 5067 422l Manual

Product: