20464
91
Zoom out
Zoom in
Previous page
1/145
Next page
Solving print quality problems
91
Troubleshooting
Solving print quality problems
Many print quality problems can be solved by replacing a supply or maintenance item that is approaching the end of its
intended life. Check the operator panel for a message about a printer consumable. See Determining the status of
supplies for information about other ways to identify consumables that need to be replaced.
Job takes longer than
expected to print.
The job is too complex. Reduce the complexity of the print job by eliminating the number
and size of fonts, the number and complexity of images, and the
number of pages in the job.
Page Protect is set to On. Set Page Protect to Off from the Setup Menu in Settings.
1 Press .
2 Press until Settings appears, and then press .
3 Press until Setup Menu appears, and then press .
4 Press until Print Recovery appears, and then press
.
5 Press until Page Protect appears, and then press
.
6 Press until Off appears, and then press .
Job prints from the wrong
tray or on the wrong
media.
The operator panel menu
settings do not match the
media loaded in the tray.
Make sure the Paper Size and Paper Type specified on the
operator panel and in the printer driver are correct for the job
being printed.
Incorrect characters print. An incompatible parallel
cable is in use.
If using a parallel interface, make sure to use an IEEE 1284-
compliant parallel cable. Lexmark part number 1329605 (10 ft)
or 1427498 (20 ft) for the standard parallel port are
recommended.
The printer is in Hex Trace
mode.
If Ready Hex appears on the display, exit Hex Trace mode;
otherwise, the job will not print. Turn the printer off and back on
to exit Hex Trace mode.
Tray linking does not
work.
Tray linking is not
configured properly.
To configure the linked trays:
Make sure the Tray x Size value in the Paper X Size menu item
in the Paper Menu is the same for all linked trays.
Make sure the Tray x Type value in the Paper X Type menu item
in the Paper Menu is the same for all linked trays.
Note: Select the paper source and the size first, and then the
screen for Paper Type is shown.
Large jobs do not collate. Collate is not set to On. Set Collation to On in the Finishing Menu in Settings or
through the printer driver.
The standard bin media
stop is not set to the
correct position for the
media size.
Set the media stop in the standard bin to the correct position.
See Using the media stop for more information.
The job is too complex. Reduce the complexity of the print job by eliminating the number
and size of fonts, the number and complexity of images, and the
number of pages in the job.
The printer does not have
enough memory.
Add printer memory or an optional hard disk.
See the Setup sheet for information on adding an optional
memory card and Installing an optional hard disk for adding
an optional hard disk.
Unexpected page breaks
occur.
The job has timed out. Set the Print Timeout menu item to a higher value from the
Timeouts menu item in the Setup Menu in Settings.
Symptom Cause Solution
91


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lexmark C522 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lexmark C522 in the language / languages: English as an attachment in your email.

The manual is 4,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Lexmark C522

Lexmark C522 User Manual - Dutch - 35 pages

Lexmark C522 User Manual - Spanish - 152 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info