Manual Levita CS35 2x20V (page 40 of 80) (English, German)

765518

Zoom out

Zoom in

1/80

back cut is complete and use wedges of wood, plastic

or aluminium to open the cut and drop the tree along

the desired line of fall.

When the tree begins to fall remove the chain saw

from the cut, stop the motor, put the chain saw down,

anf use the retreat path planned. Be alert for falling

overhead limbs and watch your footing.

Removing buttress roots

A buttress root is a large root extending from the trunk of

the tree above the ground. Remove large buttress roots

prior to felling. Make the horizontal cut into the buttress

ﬁrst, followed by the vertical cut. Remove the resulting

loose section from the work area. Follow the correct

tree felling procedure after you have removed the large

buttress roots.

Limbing a tree

Limbing is removing the branches from a fallen tree.

Branches under tension should be cut from the bottom

up to avoid bindingthe chain saw.

Bucking a log

Bucking is cutting a log into lengths. It is important to

make sure your footing is ﬁrm and your weight is evenly

distributed on both feet. When possible, the log should

be raised and supported by the use of limbs, logs or

chocks.

Follow the simple directions for easy cutting. When the

log is supported along its entire length, it is cut from the

top (overbuck).

When the log is supported on one end, cut 1/3 the

diameter from the underside (underbuck). Then make the

ﬁnished cut by overbucking to meet the ﬁrst cut.

When the log is supported on both ends, cut 1/3 the

diameter from the top (overbuck). Then make the ﬁnished

cut by underbucking the lower 2/3 to meet the ﬁrst cut.

When bucking on a slope always stand on the uphill side

of the log. To maintain control when “cutting through”,

release the cutting pressure near the end of the cut

without relaxing your grip on the chain saw handles.

Don’t let the chain contact the ground. After completing

the cut, wait for the saw chain to stop before you move

the chain saw. Always stop the motor before moving from

tree to tree.

Cutting springpoles

A springpole is any log, branch, rooted stump, or sapling

which is bent under tension by other wood so that it

springs back if the wood holding it is cut or removed.

On a fallen tree, a rooted stump has a high potential of

springing back to the upright position during the bucking

cut to separate the log from the stump. Watch out for

springpoles—they are dangerous.

WARNING

Springpoles are dangerous and could strike the

operator, causing the operator to lose control of the

chain saw. This could result in severe or fatal injury

to the operator. This should be done by trained

users.

Additional safety warnings

Some regions have regulations that restrict the use of the

machine. Check with your local authority for advice.

Never allow children or people unfamiliar with the

instructions to use the machine. Local regulations may

restrict the age of the operator.

Ensure before each use that all controls and safety

devices function correctly. Do not use the machine if the

“oﬀ” switch does not stop the motor.

Do not wear loose ﬁtting clothing, short trousers, or

jewellery of any kind.

Secure long hair so it is above shoulder level to prevent

entanglement in moving parts.

Beware of thrown, ﬂying, or falling objects. Keep all

bystanders, children, and animals at least 15 m away from

the work area.

Do not operate in poor lighting. The operator requires a

clear view of the work area to identify potential hazards.

Use of hearing protection reduces the ability to hear

warnings (shouts or alarms). The operator must pay extra

attention to what is going on in the work area.

Operating similar tools nearby increases both the risk

of hearing injury and the potential for other persons to

enter your work area.

Keep ﬁrm footing and balance. Do not overreach.

Overreaching can result in loss of balance and can

increase the risk of kickback.

Keep all parts of your body away from any moving part.

Inspect the chain saw before each use. Check for correct

operation of all controls, including the chain brake. Check

for loose fasteners, make sure all guards and handles are

properly and securely attached. Replace any damaged

parts before use.

Do not modify the machine in any way or use parts

and accessories which are not recommended by the

manufacturer.

ENGLISH

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Levita CS35 2x20V in the language / languages: English, German as an attachment in your email.

The manual is 10,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Levita CS35 2x20V Manual

Product: