477344
8
Zoom out
Zoom in
Previous page
1/40
Next page
14
15
EngEng
Sleep Timer Function
This feature allows you to fall asleep to the radio or iPod for up to 120 Minutes.
The unit shuts off automatically when the time expires.
1. Press the POWER button to turn the unit on.
2. Either tune to the desired radio station in radio mode or playback music
from the iPod.
3. To select the sleep timer to turn the unit off after 15, 30, 45, 60, 90 or
120 minutes, press the SLEEP button repeately. The display show the
indicator . The unit plays for the selected length of time then
automatically turns off.
4. To turn the unit off before the sleep timer counts down to zero, press
the POWER button at any time.
If you are falling asleep to music from an external device connected to the
AUX input, the sleep timer will shut off the power to this system but it will
not turn off the external device.
Sleep to timer
Notes :
Wake to iPod or Radio
When the alarm time is reached, the selected alarm source (iPod or Radio)
will automatically turn on. It starts softly and gradually becomes louder.
It plays for 30 minutes then shuts off and resets itself for the following day.
During the activation of the alarm source, you may press the SNOOZE
button to activate the snooze function. The alarm stops for the snooze time
(around 10 minutes) then turns on again.
To cancel the snooze before it expires, press the ALARM button.
This manual snooze operation can be repeated three times. Each time the
alarm turns on, it plays for 30 minutes (without pressing the snooze button).
To stop the alarm immediately after the alarm sounds, you may also press
the ALARM button. It resets itself for the following day.
Care and Maintenance
- Do not subject the unit to excessive force, shock, dust or extreme temperature.
- Do not tamper the internal components of the unit.
- Clean your unit with a damp (never wet) cloth. Solvent or detergent should never
be used.
- Avoid leaving your unit in direct sunlight or in hot, humid or dusty places.
- Keep your unit away from heating appliances and sources of electrical noise such
as fluorescent lamps or motors.
If the unit experiences a power surge or electric shock, it is possible that the
internal micro-controller may lock up and the unit will not respond to any
commands from the front panel controls.
1.In this event, unplug and then reconnect the AC power plug into the wall outlet.
2.Use a straightened paper clip, toothpick or similar objects to press the RESET
button located at the rear of the main unit (see the below figure). The reset
operation clears the system memory and all of your previous settings will be
erased.
Resetting the Unit
CAUTION: DO NOT USE SHARP, POINTED OBJECT TO PRESS THE RESET
BUTTON. IT MAY DAMAGE THE RESET SWITCH INSIDE THE UNIT.
RESET button
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lenco IPD-5100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lenco IPD-5100 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info