477344

Lenco IPD-5100 Manual

5
Zoom out
Zoom in
Previous page
1/40
Next page
8
9
Fully extend the FM rod antenna for the best FM radio reception.
1. Press the POWER button to turn on the unit, where the power
status indicator light on.
2. Press the FUNC button to select FM stereo or FM mono radio receiving
mode.
3. To manually tune to a desired station, repeatedly press the TUNING
/ button.
4. To automatically search for stations with strong signals, press and hold
the TUNING / button until the frequency digits on display begins to
scan then release the button. The tuner will stop on the first strong
signal it finds.
:
- Manual tune to select weaker stations that might be skipped during
automatic tuning.
- If the automatic tuning does not stop on the exact frequency of the station,
for example , it stops on 100.9 MHz instead of 100.8 MHz, use the manual
tuning method to "fine tune" to the exact frequency of the desired station.
The units allows you to store up to 20 FM stations for easy recall at any time.
1. Press the POWER button to turn on the unit, where the power status
indicator light on.
2. Press the FUNC button to select FM stereo or FM mono radio receiving
mode.
3. Tune to the radio station you want to store in memory by using the
TUNING button.
4. Press the MEM button. The preset channel number appears on display
and blinking.
5. To select desired preset station number, press the CH button.
6. To confirm preset location, press the MEM button.
7. Repeat steps 3 to 6 to store other stations, if apply.
FM Antenna
Radio Tuning
Radio Preset Stations
Preset Stations
Notes
/
/
Radio Tuner Operation
EngEng
This model adopts different iPod models. Following steps guide you
listening to iPod music.
1. Slide the "iPod tilt angle slider" for the "iPod tilt angle lever" to tilt at a
desired angle, if apply. Recommend to lay down the iPod during the
unit transportation.
2. Your iPod can now be inserted into the docking port by placing the
connector on the bottom of the iPod onto connector in the docking bay.
: Please be careful when seating the iPod into the docking to avoid
damaging the 30-pin connector on the iPod or in the docking system.
3. Slightly push the iPod to a desired tilt angle, if necessary.
4. Press the POWER button once to turn on the unit and the power status
indicator lights on.
5. Press the FUNC button to select iPod mode.
In iPod mode :
- To start playback music, press the iPod button once.
To pause the music , press the iPod button.
To resume music , press the iPod button again.
You may press the VOLUME +/- button to adjust the volume to a
desired level.
When a song playback, press and hold the button
perform high speed search forward / backward.
To skip to next or previous song, prese the button.
- To turn off the unit, press the POWER button and the power status
indicator will light off.
- When the unit is powered by external DC adaptor and once the iPod
connected to the docking station, the unit recharges the iPod battery.
Once the iPod is inserted, the unit will switch to iPod mode automatically
and neglect the current mode.
Caution
Note:
-
-
-
-/
to
-/
Listening to iPod
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lenco IPD-5100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lenco IPD-5100 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info