601607

Lenco DR-88 BT Manual

7
Zoom out
Zoom in
Previous page
1/71
Next page
GB 7
FM Radio Tuner Operation
Antenna
For the best radio reception, fully extend the rod antenna located at rear of the unit.
MENU Option
In the FM radio mode, the unit allows you to select following options.
1. Press the MENU button entering menu mode.
2. Two options, [Scan setting] and [Audio setting] can be set by pressing the / buttons from the main unit or the
TUNE +/- button from the remote control.
(a) Whilst [Scan setting] is displayed, press the ENTER button to conrm the selection.
- Then press main unit / buttons or remote control TUNE +/- buttons to display [All stations] or
[Strong stations].
Note:
[All stations] ----- By default FM scan stops at any available station (All stations). This may result in
poor quality audio from distant stations.
[Strong stations] ----- FM scan stops only at stations with good signal strength.
- Press the ENTER button to conrm the desired selection when [All stations] or [Strong stations] displayed.
(b) Whilst [Audio setting] displays, press the ENTER button to conrm selection.
- Then press main unit / buttons or remote control TUNE +/- buttons to display [Stereo] or
[Forced mono].
Note:
[Stereo] ----- By default, all stereo stations are reproduced in stereo. For weak stations, this may
result in poor quality audio. The audio quality can be improved using mono.
[Forced mono] ----- Reproduce mono audio only.
- Press the ENTER button to conrm the desired selection when [Stereo] or [Forced mono] displayed.
3. You can press the MENU button to exit menu setting mode at any time.
Auto-scan and store Preset Stations
The unit allows you to store up to 20 FM stations for easy recall at any time.
1. Press the STANDBY button to turn on the unit, where the power status indicator light on.
2. Press the FUNCTION button from the main unit or the DAB/FM button from the remote control to select FM radio
mode.
3. Press the SCAN button from the remote control until the frequency digits begin to change. The tuner will
automatically scan for stations from low to high frequency and then store them in the preset location.
Note: After each auto-scan & store operation, it will overwrite the existing preset stations by overwriting and
storing the new stations in their place.
4. To recall the preset station, press the CH +/- buttons from the remote control then press the ENTER button to
conrm selection.
FM Radio Tuning and manual store Preset Stations
1. Press the STANDBY button to turn on the unit, where the power status indicator light on.
2. Press the FUNCTION button from the main unit or the DAB/FM button from the remote control to select FM radio
mode.
FM Radio Tuning
3. You can have following ways to tune to a desired station:
(a) Press the / buttons from the main unit or the TUNE +/- buttons from the remote control with 0.05MHz
tuning step and tune to a desired radio station frequency gure.
(b) Press and hold the main unit / buttons or remote control TUNE +/- buttons and tune to a desired radio
station frequency gure then release the button.
(c) For up-scan, press the main unit button or remote control TUNE + button once then press the SCAN
button from the remote control and it will tune to the next higher radio station.
For down-scan, press the main unit button or remote control TUNE - button once then press the SCAN
button from the remote control and it will tune to the next lower radio station.
Save preset station
4. Press the MEM button from the remote control. The preset channel number appears on display and blinks.
5. To select a desired preset station number, press the CH + / - buttons from the remote control.
Note: Each time the station number changed, it will display the current frequency or “Empty” of that preset
station location.
6. To conrm preset location, press the ENTER button and “Preset store” displays a while then returns to normal
tuner mode. The newly tuned frequency will replace the frequency in the selected preset station location.
7. Repeat steps 3 to 6 to store other stations, if apply.
Notes:
● There is a few seconds delay when programming, after this delay time, the unit will automatically switch back
to normal tuner mode.
● You can overwrite a preset station by overwriting and storing the new frequency in its place.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lenco DR-88 BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lenco DR-88 BT in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info