733408
18
Zoom out
Zoom in
Previous page
1/128
Next page
EN
18
on horizontal bases, in a safe and stable way.
USAGE
> DESCRIPTION OF THE MACHINE
See pag.3-4-5.
> ASSEMBLY INSTRUCTIONS
See pag.2.
> PUT INTO SERVICE
See fig.
* Check that the master switch is turned to
“OFF” and that the water filter is fitted into
the pump’s inlet pipe.
* Screw the snap connection into place by
hand, without the aid of tools.
* Connect the water supply hose to the snap
connection. The hose must have an inside
diameter of at least 13 mm (1/2”).
* Connect the high pressure hose to the
pump’s outlet pipe. Press the high pressure
hose coupling fully down and then screw
into place by hand without the aid of tools.
* Connect the high pressure hose to the gun.
* Turn the water tap fully on. The water tem-
perature absolutely must be below 40°C.
IMPORTANT: The washer machine has to
operate with clean water in order to avoid
any damages to the washer machine itself.
* Release the gun safety catch and keep the
trigger pressed, allowing the water to flow
until all the air has been expelled.
* Fit the lance into the gun.
* Connect the plug to the power socket.
* To start the machine, press the gun trigger
and at the same time tur
n the master switch to
ON”.
FILLING UP
Fill up the tank with the fuel
indicated on the
technical data plate.
Avoid that the tank is empty when the ma-
chine is running in order not to damage the
fu
el pump.
WARNING:
Incorrect fuel shall not used as
they as provide hazard.
Fill up the detergent tank with the suggested prod-
ucts, suitable for the kind of washing to be carried
out .
WARNING:
make use only of liquid deter-
gent, do not absolutely use acid or too much
alkaline products.
We suggest you to make use of our products, which
have been studied for the use with washer ma-
chines.
> STARTING UP
See fig.
Start the machine:
turn the switch pos. 2 ( I ) ON
.
To wash with hot water:
turn the switch pos. 1 ( I ) ON
.
The burner operates when the machine is in pres
-
sion.
> HIGH PRESSURE LANCE
See fig.
> DETERGENT SUCTION
See fig.
> HIGH PRESSURE HOSE
See fig.
> WATER SUPPLY
Water supply collection
Water supply from the water main
· Connect a supply hose (not included) to the water
inlet of the unit and to the water supply.
· Open the water supply.
WARNING: (symbol) machine not suitable for
connection to the potable water mains.
The cleaner can only be connected to the wa-
ter mains if the water mains is separated by a
backflow preventer. Make sure that the hose
is at least Ø 13mm-1/2 inch and that it is rein-
forced.
WARNING: Water that has flown through
backflow preventers is considered to be
nonpotable.
IMPORTANT: Only clean or filtered water
should be used for intake. The delivery of the
water intake tap should be equal to the dou-
ble of the maximum pump range.
-
Minimum delivery rate: 15 l/ min.
-
Maximum intake water temperature: 40°C
-
Max inlet water pressure: 1Mpa
Place the cleaner as close to the water supply
system as possible.
Water supply from an open container
· Unscrew the coupling part for the water inlet.
· Screw the suction hose with filter (not included) onto
the water connection of the unit.
· Hang the filter in the container.
- 3
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lavorwash XTR 1007 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lavorwash XTR 1007 in the language / languages: All languages as an attachment in your email.

The manual is 7,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info