646776

Laserliner MultiTest-Master Manual

9
Zoom out
Zoom in
Previous page
1/136
Next page
MultiTest-Master
09
GB
2
ON / OFF
3
AUTO OFF FUNCTION
When you switch the device on, it shows the current ambient
temperature in °C on the display. To display the value in °F, press
the „Unit“ button. By pressing the „Mode“ button, you can get the
device to display the highest (MAX), lowest (MIN), average (AVG)
or difference value (DIF) in addition to the current measured value.
As its name suggests, the „HOLD“ button enables you to hold the
current measured value.
Ambient temperature
5
When you switch the device on, the „AUTO OFF FUNCTION“ is activated automatically. After 20 minutes,
the device switches off automatically unless one of the buttons is pressed. To activate or deactivate the
device‘s „AUTO OFF FUNCTION“, press the „SET“ button while pressing and holding down the „ON/OFF“
button. For optimum measurements, please wait approximately 15 minutes after switching on the measu-
ring device so that it has time to adapt to the new ambient conditions in a particular room.
Relative humidity may be deÖ ned as the ratio between the air‘s
current water vapour content and the maximum that it can contain
at the same temperature and constant pressure. Hot air can hold
more water vapour than cold air. At 100% relative humidity, the
saturation point has been reached and the air cannot hold any more
water vapour.
Press the „Temp/%rH“ until a measured value in % relative humidity
(%RH) appears on the display. By pressing the „Mode“ button,
you can get the device to display the highest (MAX), lowest (MIN),
average (AVG) or difference value (DIF) in addition to the current
measured value. As its name suggests, the „HOLD“ button enables
you to hold the current measured value.
Relative humidity
6
SET
TEMP/%RH
O
SET
TEMP/%RH
O
1. 2.
Activated Deactivated
In the event of rapid temperature × uctuations (± 1°C), the sensor needs to adapt to the new condi-
tions. Consequently, it takes a certain amount of time for a stable value to be established.
!
In the event of rapid × uctuations in relative humidity (± 1%), the sensor needs to adapt to the new
conditions. Consequently, it takes a certain amount of time for a stable value to be established.
!
4
Display illumination
If visibility is poor, switch on the display illumination. In order to pre-
serve the batteries, the illumination switches off automatically after
10 seconds. To reactivate it, simply press the button again.
HOLD
MODEMODE
dB
UNIT
ANEMO
LUX
SET
HOLD
MODEMODE
dB
TEMP/%RH
UNIT
ANEMO
LUX
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Laserliner MultiTest-Master at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Laserliner MultiTest-Master in the language / languages: All languages as an attachment in your email.

The manual is 7,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info