646737
12
Zoom out
Zoom in
Previous page
1/88
Next page
DualAxis-Laser
DEUTSCH12
Digitale Neigungsfunktion
Die horizontale Ebene kann digital in X- und Y-Achse geneigt werden.
Die maximale Neigung beträgt in einer Ebene bis 7,999%, die Summe
der beiden Achsen bis 10% in 2 Ebenen (X-Achse + Y-Achse). Auf der
großen LC-Anzeige werden die Werte dargestellt und können getrennt
voneinander eingegeben werden.
Einstellung der X-Achse: Die X-Taste (27) drücken. Auf der LC-Anzeige
blinkt die erste Stelle des X-Achsen Wertes. Mit den Plus/Minus-Tasten
(28) an dieser Stelle auswählen, ob der Wert positiv ("0") oder negativ
("-") sein soll. Die nächsten Stellen mit der X-Taste (27) anwählen.
Mit den Plus/Minus Tasten (28) können die Zahlenwerte eingestellt
werden. Mit der Enter-Taste (29) die Eingabe bestätigen, wenn der
komplette Wert eingestellt ist. Anschließend stellt sich das Gerät auf
den gewünschten Wert ein.
Wichtig: Während des Nivelliervorgangs kann keine weitere
Eingabe erfolgen, in der LC-Anzeige blinkt "SLOPE" (19). Wenn
"SLOPE" permanent angezeigt wird, ist die Nivellierung abgeschlos-
sen und es können neue Werte eingestellt werden.
Einstellung der Y-Achste: Die Y-Taste 31 drücken und genauso verfahren wie bei der
Einstellung der X-Achse.
Hinweis: Bei der digitalen Neigungsfunktion ist die Sensor-Automatic aktiv.
Manuelle Neigungsfunktion:
Bei dieser Funktion wird die Sensor-Automatic ausgeschaltet. Jetzt kön-
nen große Neigungen angelegt werden. Dazu die auto/man-Taste (32)
drücken. Im LC-Display erscheint "MAN" (24).
Das Gerät in den gewünschten Winkel neigen. Mit der optio-
nalen Winkelplatte, Art-Nr.: 080.75, kann die Neigung einfach
eingestellt werden. Dazu ein Kurbelstativ verwenden, z.B.
Art-Nr: 080.36.
Hinweis: Der DualAxis-Laser kann im auto/man-Betrieb die
Neigung nicht motorisch verfahren.
Wichtig: Im auto/man-Betrieb kann nicht horizontal nivelliert
werden, da die Sensor-Automatic nicht aktiv ist.
In 1 Ebene
In 2 Ebenen
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Laserliner DualAxis-Laser at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Laserliner DualAxis-Laser in the language / languages: English, German, Dutch, Danish, French, Finnish as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info