646737
11
Zoom out
Zoom in
Previous page
1/88
Next page
DualAxis-Laser
DEUTSCH 11
Einrichten
Das Gerät auf einer möglichst ebenen Fläche aufstellen oder auf einem
Stativ befestigen.
AN/AUS-Taste (34) beim Rotationslaser drücken.
Das Gerät nivelliert sich in einem Bereich von + 5 ° automatisch aus.
Wenn die Nivellierung erfolgt ist, dreht der Laser mit 600 U/min. Die Drehzahl kann
mit der Rotations-Taste (35) geändert werden (0, 300, 600, 1100 U/min). Während der
Ausrichtung blinkt der Laser.
Wichtig: Durch die hohe Messgenauigkeit kann die automatische Nivellierung bis zu 3
Minuten dauern.
BackLight: Die Enter Taste (29) beim Rotationslaser mindestens 2 Sekunden drücken
und das Display wird beleuchtet. Durch erneutes Drücken wird die Beleuchtung ausge-
schaltet.
Den Laserempfänger SensoLite mit der Taste 17 anschalten. Jetzt kann der Laserstrahl
empfangen werden. Dabei beachten: Der Laserempfänger reagiert schneller, wenn der
Rotationslaser auf eine hohe Drehzahl eingestellt wird.
Standby Betrieb
Mit der AN/AUS-Taste (37) am Commander DAL 50 kann der Rotationslaser in einen
Standby Betrieb geschaltet werden. Dabei bleiben die voreingestellten Werte erhalten,
empfehlenswert besonders im digitalen Neigungsmodus.
Hinweis: Wenn der Rotationslaser direkt am Gerät mit der AN/AUS-Taste (34) ausge-
schaltet wird, werden alle voreingestellten Werte gelöscht.
Tiltfunktion
Um das Gerät vor Lageveränderung durch Fremdeinwirkung zu schützen,
muss die Tiltfunktion aktiviert werden. Dazu die Tilt-Taste (33) drücken,
siehe auch den Abschnitt über Anti-Drift-System. Die Tiltfunktion ist aktiv, wenn im
LC-Display "Tilt" (22) permanent angezeigt wird.
Hinweis: Im Standby Betrieb ist die Tiltfunktion nicht aktiv und das Gerät wird nicht
vor Lageänderung geschützt.
i
Hinweis: Wenn das Gerät zu schräg aufgestellt wurde (außerhalb von 5°), ertönt ein
Warnsignal, der Rotorkopf steht still und LEV blinkt in der LC-Anzeige. Dann muss das
Gerät auf einer ebeneren Fläche aufgestellt werden.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Laserliner DualAxis-Laser at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Laserliner DualAxis-Laser in the language / languages: English, German, Dutch, Danish, French, Finnish as an attachment in your email.

The manual is 3,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info