680891
2015
Zoom out
Zoom in
Previous page
1/2025
Next page
(LANmonitor) using an SNMP trap. Using this error message, the corresponding parameter in the configuration can be
checked and changed if necessary. Thus is it always necessary to verify the error messages on both sides.
ResponderInitiatorMessage
The maximum number of possible VPN channels has been
reached.
xxLicense exceeded - no more VPN tunnels
available (Responder, IKE)
The router to the remote gateway could not be found.
Please check the public IP address or the DynDNS name of
the remote device.
xxNo route to remote gateway
In dynamic VPN, the outgoing call could not be
authenticated with the PPP data sent. Please check the PPP
xDynamic VPN - no PPP table entry
matched
username and PPP password on both sides under
"Configure --> Communication --> Protocols --> PPP list
--> Remote site".
The incoming call cannot be authenticated with the PPP
data received. Please check the PPP username and PPP
xDynamic VPN - no PPP table entry
matched
password on both sides under "Configure -->
Communication --> Protocols --> PPP list --> Remote site".
A time limit was reached. The router on the remote side is
no longer responding. Please check the VPN error message
in the LANmonitor on the remote device.
xxIKE or IPSec establishment timeout
The LCP polling failed. Please check on the remote device
whether ping blocking is enabled in the firewall menu under
"Configure --> Firewall --> General --> Ping blocking"
Line polling to remote gateway failed
The holding time of the VPN tunnel under "Configure -->
VPN --> Connection list --> Names" is set to Short hold
No entry in polling table and keep alive
in configured
(9999 sec.). However, the required ICMP polling is missing.
Please add them under "Configure --> Communication -->
Remote Sites --> Polling Table". As remote site, enter the
VPN remote device, for the IP address enter an IP address
from the LAN at the remote site.
The fee limit under "Configure --> Costs --> Fees - Limit
(ISDN)" was reached. Please reboot the device.
xDynamic VPN - predefined charge limit
exceeded
The time limit under "Configure --> Costs --> Time limit
(ISDN)" was reached. Please reboot the device.
xDynamic VPN - preset time limit exceeded
The ISDN call number for the remote device for dynamic
VPN is missing. Please enter the call number under
xDynamic VPN - no ISDN call number for
negotiator channel
"Configure --> Communication --> Remote sites --> Name
list (ISDN) --> Name".
While establishing multiple ISDN connections, a limit was
reached. Please check under "Configure --> Management
Dynamic VPN - Multiple connections on
ISDN interface for negotiator channel not
allowed --> Interfaces --> Interface Settings --> ISDN --> Max.
outgoing calls".
The fee limit under "Configure --> Management --> Costs
--> Charge limit (ISDN)" was reached. Indicated by a
synchronized blinking of the Power LED.
xPredefined charging limit exceeded
The time limit under "Configure --> Management --> Costs
--> Time Limit (ISDN)" was reached. Indicated by a
synchronized blinking of the Power LED.
xPredefined time limit exceeded
The IP address of the PPTP selected has not been entered.
Enter the IP address under "Configure --> Communication
--> Protocols --> PPTP list". Also see .
xNo IP address for PPTP server
2015
Reference Manual
20 Appendix
2015


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lancom LCOS 9.10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lancom LCOS 9.10 in the language / languages: English as an attachment in your email.

The manual is 54,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info