729369
44
Zoom out
Zoom in
Previous page
1/122
Next page
LANCOM 1722 VoIP – LANCOM 1723 VoIP – LANCOM 1724 VoIP – LANCOM 1823 VoIP
Chapter 2: Installation
44
EN
the device light up continuously. Once the switch is released the
device will restart with the restored factory settings.
This hard reset causes the device to start with the default factory set-
tings; all previous settings are lost!
Note that resetting the device leads to a loss on the WLAN encryption
settings within the device and that the default WEP key is active
again.
Only LANCOM
1823 VoIP
Main connector for the WLAN module.
2.4 Hardware installation
Installation of the LANCOM Router involves the following steps:
LAN – first of all connect your LANCOM Router to the LAN or to an indi-
vidual PC. Plug in one end of the supplied network cable (green connec-
tors) to a LAN connector on the device , and the other end into an
available network connector socket in your local network, a free socket on
a switch or hub, or the networking connector of an individual PC.
The LAN connectors use autosensing to recognize the data rate (10/100
Mbit) and the type (node/hub) of attached network devices. It is possible
to connect devices of different speeds and types in parallel.
Avoid having multiple unconfigured LANCOMs at once within a single
network segment. Any unconfigured LANCOM takes on the same IP
address (ending in '254'), and so address conflicts could arise. To
avoid problems, multiple LANCOMs should be configured one after
the other with the respective device being assigned with a new and
unique IP address (not ending in '254') each time.
ADSL – connect the ADSL interface with the splitter by using the sup-
plied ADSL connector cable (transparent connectors).
Connection to the ISDN – to connect the LANCOM VoIP Router to the
ISDN, plug in one end of a supplied ISDN cable (light-blue connectors) to
an ISDN interface in TE mode. When shipped, the ISDN interfaces marked
with
are set up in TE (external) mode. Plug in the other end of the
ISDN cable into an ISDN/S
0
point-to-point line connector or point-to-
multipoint line connector.
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lancom 1823 VoIP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lancom 1823 VoIP in the language / languages: English as an attachment in your email.

The manual is 2,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info