719427

Lanaform LA120125 Manual

5
Zoom out
Zoom in
Previous page
1/44
Next page
5 / 44 English
EN FR NL DE ES IT PL CS SK SL HR BG
Electricity consumption
The warm mist function uses more energy
because it has to heat the water.
Preparation
1
1 Place the NAPO humidier in
the room half an hour before
turning it on so that it can
adjust to room temperature.
2 Make sure it is always placed on a
hard, at and horizontal surface. Keep
it slightly away from walls and heat
sources such as stoves, radiators, etc.
3 Make sure the device is clean
before starting to use it.
4 Remove the reservoir lid (1).
Then pour fresh, preferably
demineralised water into the
reservoir (5). Replace the cover.
5 Make sure your hands are com-
pletely dry when connecting (and
disconnecting) the device.
6 The humidier is now working.
Instructions for use
2
1) Switching the device on and o:
•
Press the ON/OFF button (1) to switch on
the device. Its default mode is cool mist,
at average emission intensity and the
LED screen displays the current humidity
level of the ambient air.
the LED screen displays the
humidity level between 30 and
80%. If it displays “LO”, the
humidity level of the ambient
air is less than 30%. If it displays
“HI”, the humidity level of the
ambient air is more than 80%.
• To turn the device o, press the button
again. All the functions will stop, except
the fan, which will continue to run for
15 seconds.
if the reservoir is empty, the
device emits a sound signal and
a red light indicator will light
up on the ON/OFF button. The
LED screen will also display “E1”.
The device does not emit any
more mist: ll the reservoir so
that it runs normally again.
2) Select a light or night mode:
• When the device is on, it does not emit
an atmospheric light by default.
• Press the button that selects the light
mode a rst time (2): the light is activat-
ed and automatically changes colour.
•
Press it a second time and the colour
will be set.
• Press it a third time and the LED screen
will display “SP” for 5 seconds. The de-
vice will go into night mode.
- All the lights are o unless the mode in-
dicates otherwise (note that if the warm
mist is activated, the button indicator ()
will stay on for  seconds).
- The device will run for  hours –  hours
at medium intensity, then  hours at low
intensity.
- The humidity level is checked at  and
the device will stop running when the am-
bient air reaches this level and resumes
when the rate drops.
• Press a fourth time: the device discon-
nects from the night mode and resumes
its previous emission intensity.
3) Select the heating function:
•
When the device is on, press the heat-
ing function button (3) to set it going.
When this function is active, a heating
resistor heats up the water in the base
to counteract the bacteria and creates
a warm mist.
• Press the button again to turn the heat-
ing function o.
the heating function is
independent of all the other
functions and modes. It can
therefore be activated and
deactivated at any time.
never touch the heating
resistor (Fig.1, point 11)
before it has cooled down!
In the event of accidental
burns, consult a doctor!
4) Adjust the timer:
When the device is on, press the button
repeatedly that sets the timer () to set
the device going for  to  hours. The LED
screen will display the time selected or “CO”
for continuous for  seconds.
5) Adjusting the humidity level:
When the device is on, press the button that
sets the humidity level () repeatedly to set
the automatic humidity control going at the
level required from  to  in increments
of . The LED screen will display the level
selected or “CO” for “by default” for  sec-
onds. We recommend a level of humidity
between approximately  and . The
device will stop running when the ambient
air reaches the required level and resumes
when this rate drops.
6) Adjusting the emission intensity:
• When the device is on, it emits mist at
a medium intensity.
•
Press the button for selecting the
emission intensity (6) once: the device
will emit mist at the highest intensity
intensity.
• Press a second time and the device will
emit mist at the lowest.
•
Press a third time and the device will
emit mist at medium intensity.
- Only use fresh, distilled or demineralised
water to avoid any malfunction.
- Do not pour water into the diuser sprin-
kler tip (Fig. , point ) in order to avoid any
malfunction and risk of re.
- The reservoir must be kept clean. Please
refer to the cleaning instructions below.
EVEN THOUGH THERE IS A
SAFETY DEVICE THAT STOPS
THE TRANSDUCER FROM
WORKING, DO NOT LEAVE THE
DEVICE CONNECTED WHEN
YOU ARE NOT USING IT.
Diusing essential oils
To diuse essential oils, push the essential
oil tray (Fig. , point ) so that you can re-
move it. Pour  drops onto the pad inside.
Make sure that the oil does not touch any
other part of the device as this may dam-
age the materials.
Additional information
about the use of essential oils
•
Before using essential oils, please check
the harmful eects that use of these
products may have on your health.
•
Always choose quality essential oils that
are pure, 100% natural and intended for
diusion. Use them in moderation and
with care. Follow the instructions and
warnings stated on the packaging of
the essential oils, making sure in par-
ticular that:
•
Pregnant women, people with epilepsy,
asthmatics and people who suer from
allergies, those with heart problems
or serious illnesses should not use es-
sential oils.
•
Essential oils should be used only for
periods not exceeding 10 minutes in
the room of a baby (under 3 years old)
and only when the baby is not actually
in the room.
• Make sure that children and minors do
not play with or use the device.
•
Just a few drops (3 to 4 drops at most) of
essential oils are sucient to ensure that
the device works properly and the scent
is diused. Excessive use of essential oils
could damage the device.
• Make sure you pour water into the res-
ervoir rst before adding the drops of
essential oils.
• Lanaform cannot be held liable in the
event of accidental damage resulting
from any use contrary to the instructions
given in these instructions for use.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lanaform LA120125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lanaform LA120125 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 1,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info