699083

Lamax Shield Plus Manual

18
Zoom out
Zoom in
Previous page
1/132
Next page
15
Installation Tips
Installing the Magnetic Sensor
The magnetic sensor can be installed on windows, doors or any other object that can be opened or
closed. The sensor consists of two parts, the larger sensor part and the smaller magnet part. The sensor
attaches to the frame and the magnet to the moving part.
When installed correctly, the LED on the magnetic sensor blinks once when the two parts are separa-
ted by more than a centimetre. When closed, the spacing between the two parts must not be more
than one centimetre.
Both parts of the magnetic sensor attach with double sided tape or screws.
Do not install the magnetic sensor on metal surfaces or in places where there are a large number of
metal parts. Ensure the LED blinks when the window or doors opens.
IMPORTANT: On both parts of the magnetic sensor there is an arrow. Parts must be xed with the
arrow pointing towards you.
Connecting the Magnetic Sensor
1. Ensure the sensor is mounted next to the magnet at a distance of less than one centimetre.
2. Enter the passcode into the control panel and press “RECORD”.
3. Record button lights up.
4. Separate the two parts of the sensor from each other at a distance of greater than one centimetre.
5. The sensors will record the event. When the sensor is successfully paired, the control panel will beep.
If the control panel beeps twice, it means the sensor has already been paired.
Electric Lock Output
The PUSH and GND connector of the electric lock can be connected to the PUSH and GND at the rear
of the control panel.
Once the security system is connected to the electric lock and disarmed, the control panel sends a
signal to the lock and unlocks it.
NOTE: Doors equipped with an electric lock automatically unlock when there is a power failure. We strongly
recommend connecting a backup power device.
Installing the Control Panel
The control panel can be mounted directly on the wall or using the stand on any at surface.
Installing on the Wall
The control panel can be mounted on the wall using the bracket and screws included. Insert the con-
trol panel into the bracket from top to bottom. The bracket ensures that the tamper switch is conti-
nually depressed.
Installing on a Flat Surface
Using the stand, the control panel can be installed on any at surface. Insert the control panel into the
stand from top to bottom. The stand ensures that the tamper switch is continually depressed.
IMPORTANT: Pressing the tamper switch several times resets the system.
Assigning Sensors to Modes
Each sensor can be assigned to one of four dierent modes. The security system recognizes home
mode, normal mode, 24-hour mode and single zone mode.
IMPORTANT: Before you set the security system, decide which sensor to put in which group. If you
want to change which group the sensor is in, the sensor must be disconnected from the control
panel.
The gure below shows the sensor switch setting for each group.
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Lamax Shield Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Lamax Shield Plus in the language / languages: English, German, Polish as an attachment in your email.

The manual is 2,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info