812600
8
Zoom out
Zoom in
Previous page
1/36
Next page
MANUAL FOR USE AND MAINTENANCE
8 LSC 001 -UK- REV. 06
HEATING PHASE AND PRESET PHASE FOR OPERATION
(Range New - Rapid - Spazio - S3)
In the S5 1 GROUP range , turn the switch knob to position 2 (boiler heating element ON )
a) Fasten the lter holders (11) to the delivery groups (16).
b) Open the steam valves (5) (turning them anticlockwise) and leave them open; then move the steam
wands (8) over the grid (10).
c) Wait for steam to come out of the wands (8) (about 15 / 20 minutes) then close the steam valves (5)
(turning them clockwise).
d) Wait for the appliance to reach operating temperature, which can be seen on the pressure gauge (4)
on the appliance (1 bar pressure).
On the Seletron model it is possible to view the temperature in ° set during the installation phase
being reached on the display (33).
NOTE. The operating temperature is the boiler temperature during normal operation.
e) The appliance is ready for use.
HEATING PHASE AND PRESET PHASE FOR OPERATION
(Range S5 - Compact)
a) Fasten the lter holders (11) to the delivery groups (16).
b) Open the steam valves (5) (moving the lever upwards) and leave them open; then move the steam
wands (8) over the grid (10).
c) Wait for steam to come out of the wands (8) (about 15 / 20 minutes) then close the steam valves (5)
by moving the lever back to its original position.
d) Wait for the appliance to reach operating temperature, which can be seen on the pressure gauge (4) on
the appliance (1 bar pressure). For S5 range models, check the control panel (13) to make sure that the
temperature set at the time of installation, given in °C, has been reached. During the heating phases,
make sure that the symbols on the control panel (13) switch on in progression as the temperature rises.
The display will start to show this as soon as the temperature reaches 105 °C and will continue until
the appliance reaches its operating temperature (the set temperature symbols will go from ashing to
xed). Each time that the temperature drops to below the SET level, the symbol indicating the operating
temperature will start to ash (heating phase) until the set temperature is reached.
NOTE. The operating temperature is the boiler temperature during normal operation.
e) The appliance is ready for use.
COFFEE PREPARATION
a)
Remove a lter holder (11/a or 11/b according to whether 1 or 2 cups of coffee are required) from the
delivery
group (16).
b) Fill it with ground coffee, taking care not to leave any coffee powder on the top edge of the lter holder.
Press down the coffee with the special coffee tamper provided.
c) Firmly re-attach the lter holder to the group, without tightening it excessively.
d) Place one or two cups below the lter holder (according to whether it is for 1 or 2 cups of coffee).
e) Push the button (12) on the delivery group until the required of amount of coffee has been delivered,
then manually stop the delivery function by pressing the same button again.
f) For EK and Seletron models, it is sufcient to press any of the coffee delivery buttons (25-26-27-28)
with pre-set doses (set during installation) or alternatively, to use the manual delivery button (29).
NOTE. To stop coffee delivery earlier after using one of the buttons with pre-set doses, just press
the button (29) on the same touchpad (except for range Super 3000 Seletron model).
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for La Spaziale RAPID at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of La Spaziale RAPID in the language / languages: English as an attachment in your email.

The manual is 1.91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info