20377
63
Zoom out
Zoom in
Previous page
1/110
Next page
Chapter 1 Using the Operator Panel
1-53
If the toner container was replaced when Replace toner
TK-400 was not displayed, reset the toner counter as follows
so that an accurate toner gauge measurement is indicated on
the status page. Note that if this operation is performed
when the toner container is not replaced, the toner gauge
measurement will not be indicated correctly.
Also see the
Installation Guide
supplied with the toner kit
when replacing the toner container.
Press the MENU key.
Press the or key repeatedly until Life
Counters > appears.
Press the key.
Press the or key repeatedly until >New Toner
Installed appears.
Press the ENTER key. A question mark (?) appears.
Press the ENTER key. The toner counter is reset.
Press the MENU key. The message display returns to
Ready.
You can select the language of the messages on the message
display by following the procedure given below.
Press the MENU key.
Press the or key repeatedly until Others > ap-
pears.
Press the key.
Press the or key repeatedly until >MSG
Language appears. The default message language is
English.
To change the language, press the ENTER key. A
blinking question mark (?) appears.
Press the key. The display cycles through the
available selections in the following order (the key
cycles in the reverse order):
English
Francais
Deutsch
Italiano
Nederlands
Espanol
Portugues
Press the ENTER key.
Press the MENU key. The message display returns to
Ready.
When the printer receives no data for a certain time, it times
out and releases the current interface: it prints whatever
data it has in its buffer and feeds out the page. You can ad-
just the time-out time as follows:
Press the MENU key.
Press the or key repeatedly until Others > ap-
pears.
Press the key.
Press the or key repeatedly until >Form Feed
Time Out appears. The default setting is 0 seconds.
Resetting the Toner Counter
Life Counters >
>New Toner
Installed
>New Toner
Installed ?
Selecting the Message Language
Others >
1
2
3
4
5
6
7
1
2
3
>MSG Language
English
>MSG Language
? English
Setting the Automatic Form Feed Timeout
Others >
>Form Feed
Time Out 000sec.
4
5
6
7
8
1
2
3
4
63


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kyocera FS6020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kyocera FS6020 in the language / languages: English as an attachment in your email.

The manual is 4,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info