Manual Kuppersbusch EEB 9640.0 (page 10 of 10) (English)

661111

Zoom out

Zoom in

1/10

Installation instructions for fitter

Statutory regulations and the connection specifications issued by the

local power company must be observed to the letter.

Safeguard the cooker by means of line-protecting switches, fuses or con-

tactors with at least 3 mm contact opening width. Switch off the cooker by

means of these safety devices before connecting up the oven, carrying out

repair work or replacing the light bulb. It must be impossible to touch live

components under kitchen operating conditions. The earth wire must be

long enough so that when the mains lead cleat fails, the live wires of the

connecting cable are subjected to tension before the earth wire.

The safety devices must be easily accessible.

Electrics

WARNING!

This appliance must be earthed!

Disconnect from mains before each operation!

Electrical requirements (for UK and Republic of Ireland only)

Check that the voltage stamped on the rating plate corresponds with

your house electricity supply, which must be AC (alternating current).

Electrical connection of the apppliance must be performed by a trained

electrician. The legally recognized regulations and the connection require-

ments of the electricity board serving your area must be fully complied

with.

WARNING! Should the oven be supplied with a continental two-pin plug

fitted, then this plug must be cut off from the connection cable. Dispose

of the plug safely; do not insert it in a 13 A socket elsewhere in the

house as this could cause a shock hazard.

Connection values

230 V/400 V 2N

50 Hz (230 V

in UK)

for connection 2N

fuse rating 16 A (cable 4 x 1,5

)

for connection 1N ~ fuse rating 25 A (cable 3 x 2,5

)

Use H05 RR-F or H07 RN cable; length around 2 meters.

Heating element voltage: 230 – 240 V

Electrical supply to your oven

Your oven must be installed by a qualified electrician in line with all electrical

and installation requirements published by the Institute of Electrical Engineers.

A double pole switch must be provided no further than 2 metres from the app-

liance to the electrical supply. All supply current and earth conductors must be

able to withstand an ambient temperature of 75 °C. The appliance must be con-

nected using cable (not supplied) in accordance with the following code:

Green or Green / Yellow Earth

Black or Blue Neutral

Red or Brown Live

As the coloured wires in the mains lead of this appliance (not supplied) may

not correspond with the coloured markings identifying the terminals in the

socket, proceed as follws:

–

The wire coloured green / yellow must be connected to the terminal

in the socket marked E, or marked by the earth symbol

+, or which

is coloured green resp. green / yellow.

–

The blue wire must be connected to the terminal marked N, or which

is coloured black.

–

The brown wire must be connected to the terminal marked L, or

which is coloured red.

Note: This appliance is intended to be permanently connected to fixed wiring.

Installation in a fitted kitchen

You need the following housing area to fit your oven correctly.

Dimensions

(mm)

Oven

(including outer casing)

Housing

Height 888 877

Width 594 560

Depth 560 555 (min)

The oven is designed to fit into a cabinet of 600 mm width.

The oven should be built into kitchen units, but you must ensure that it is

properly ventilated.

In the diagram the oven is ventilated by means of the space in the top of

the kitchen cabinet (see diagram).

–

Lift the oven into position on the shelf, taking care not to lift it by the

door handle.

–

If you lower the oven door, you will see 8 screw holes, 4 on each

side of the oven.

–

The oven should then be secured to the housing by fitting screws into

these holes.

Remember the housing should not be free standing but should be

secured to the wall and/or adjacent fittings.

–

Attach the side frames as indicated in the following figure.

10 EEB 9640.0

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kuppersbusch EEB 9640.0 in the language / languages: English as an attachment in your email.

The manual is 0,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kuppersbusch EEB 9640.0 Manual

Product: