639542

Kubota T2380 Manual

67
Zoom out
Zoom in
Previous page
1/78
Next page
PERIODIC SERVICE52
[T2080, T2380]
1. The drain plug is located on the starter side of the oil
pan. Clean the area around the oil drain plug and the
oil fill cap/dipstick.
2. Remove the drain plug and the oil fill cap/dipstick.
3. Allow the oil to drain and then reinstall the drain plug.
Tighten 13.6 N-m (10 ft. lb.).
4. Remove the old filter and wipe off the filter adapter with
a clean cloth.
5. Place a new replacement filter in a shallow pan with
the open end up. Pour new oil, of the proper type, in
through the threaded center hole. Stop pouring when
the oil reaches the bottom of the threads. Allow a
minute or 2 for the oil to be absorbed by the filter
material.
6. Apply a thin film of clean oil to the rubber gasket on the
new oil filter.
7. Install the new oil filter to the filter adapter. Hand
tighten the filter clockwise until the rubber gasket
contacts the adapter, then tighten the filter an
additional 3/4-1 turn.
8. Fill the engine with the proper oil to the "FULL" or "F"
mark on the dipstick. Always check the oil level with
the dipstick before adding more oil.
9. Reinstall the oil fill cap/dipstick and tighten securely.
10.Start the engine and check for oil leaks. Recheck oil
level before placing the engine into service.
Stop the engine, correct any leaks, and allow a minute
for the oil to drain down, then recheck the level on the
dipstick.
A To prevent extensive engine wear or damage, always
maintain the proper oil level in the crankcase. Never
operate the engine with the oil level below the "ADD"
or "L" mark or above the "FULL" or "F" mark on the
dipstick.
EVERY 200 HOURS
BCleaning Bendix Starter [T1880]
Consult your local KUBOTA Dealer for this service.
EVERY 500 HOURS
BCleaning Solenoid Shift Starter
[T2080,T2380]
Consult your local KUBOTA Dealer for this service.
EVERY 600 HOURS
BReplacing Transaxle Filter
To avoid serious injury:
A Park the machine on a firm and level surface.
A Apply the parking brake.
A Be sure to stop the engine and remove the key
before changing or checking the oil.
A Allow transmission case to cool down
sufficiently; oil can be hot and may cause
burns.
1. Apply the bypass valve.
2. Remove the hex head bolts (4), and filter guard (3).
Clean any loose debris from around the perimeter of
the oil filter (2).
3. Place an oil drain pan (12" or more diameter and 8 qt.
capacity is optimal) beneath the oil filter. Remove the
oil filter (2) and discard it.
A Always replace the filter when preforming any internal
maintenance to the transaxle.
4. Remove the metal oil drain plug (8) from drain port and
allow any remaining oil to drain from the transaxle.
5. After the oil has drained, inspect all parts for excessive
wear or damage. Replace if necessary. Then install
the metal oil drain plug (8) into transaxle. Torque the
plug (8) to 1.70 N-m (1.25 lbf-ft).
6. Wipe the filter base surface off and apply a film of new
oil to the gasket of the new replacement filter (Hydro-
Gear part number 52114).
7. Install the new filter by hand, turn 3/4 to 1 full turn after
the filter gasket contacts the filter base surface.
(1) Engine oil filter cartridge (A) "MOUNTING SURFACE"
… 67 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kubota T2380 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kubota T2380 in the language / languages: English as an attachment in your email.

The manual is 5,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info