672684

Krups EVIDENCE EA8908 Manual

30
Zoom out
Zoom in
Previous page
1/306
Next page
Automatic cleaning programs
Automatic cleaning program of the coffee circuit
A message on the screen will indicate when a cleaning program needs to be run for the appliance.
To run this cleaning program, you will need a container which holds at least 0.6 l, and which should be placed beneath
the coffee outlets and the steam nozzle, and a KRUPS cleaning tablet. Fig. 34a. Carefully follow the instructions given
on the screen. It is also possible to run a cleaning cycle via the Maintenance menu.
!
Important: You do not have to run the cleaning program as soon as the appliance requests it, but it must be
done reasonably soon after. If cleaning is postponed, the alert message will remain illuminated until
the process is completed.
The automatic cleaning program comprises two phases: a cleaning cycle and a rinsing cycle, and lasts about 13
minutes.
!
Important: If you unplug your machine during the cleaning cycle, or if there is a power failure, the cleaning program
will continue from the current phase when the power is returned. It is not possible to postpone this
process. This is essential to ensure that the water circuit has been correctly rinsed. In this case, a new
cleaning tablet may be necessary. Complete the full cleaning program in order to remove all of the
cleaning product which is harmful to health.
Cleaning the “One Touch Cappuccino” block
To complete a cleaning program, you will require two containers (minimum 0.6 L) and KRUPS cleaning liquid.
You can start the cleaning cycle by pressing button .
Then selecting “Maintenance” “Milk Cleaning”. Follow the instructions on the screen.
Dismantling the “One Touch Cappuccino” block
In addition to rinsing, it is necessary to clean the different elements of the block every time after using. To dismantle
the block, follow the following instructions:
Remove the milk tube, Fig. 21.
Remove the front lid of the coffee milk nozzles. Slide it downwards and pull it towards you. Fig. 22.
Remove the “One Touch Cappuccino” block by pulling the upper part of the block Fig. 23.
Completely dismantle the block. Fig. 24.
Remove the milk tube connector Fig. 25.
Clean all of the dismantled parts (block, connector and milk tube) with soapy water. Then rinse them in hot water. Fig.
26.
Once the elements are clean and dry, assemble the block and return them to their original position. Fig. 27.
Replace the font lid of the block. Fig. 28. Replace the connector in the milk tube Fig 29 (opposite side of the bevelled
side) and plug in the block. Fig. 30.
Automatic descaling program of the steam circuit
Warning: if your appliance is tted with our Claris - Aqua Filter System cartridge, remove the cartridge before
descaling.
A message on the screen will indicate when a descaling program needs to be run for the appliance. The frequency of
this program depends on the quality of the water used and on whether a Claris Aqua Filter System lter is used or not
(the harder the water, the more often the appliance has to be descaled).
!
Important: You are not obliged to carry out this program immediately the appliance requests it, but it must be
carried out reasonably soon afterwards. If descaling is postponed, the alert message will continue to
be displayed until the process is completed.
When the descaling alert level is reached and displayed, press to run the descaling program. To delay it, press
.
Once the procedure has been launched, follow the instructions provided on the screen. It is also possible to run a
descaling cycle via the “Maintenance” menu “Descaling”.
To carry out a descaling program, you will require a container with a capacity of at least 0.6 L which should be placed
beneath the One Touch Cappuccino block and a KRUPS descaling sachet (40 g). Fig. 34b
Fill the water tank up to the CALC mark then pour in the contents of one sachet of descaler.
The descaling program comprises three phases: a descaling cycle and two rinsing cycles. The program lasts
approximately 20 minutes.
28
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Krups EVIDENCE EA8908 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Krups EVIDENCE EA8908 in the language / languages: All languages as an attachment in your email.

The manual is 2,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info