390656
8
Zoom out
Zoom in
Previous page
1/52
Next page
8
English 900 WTSE
The angle grinder can be used universally for cutting
and treating metals and stone. For high speeds, only
use the cutting and grinding items approved for the
machine.
Before operating the machine, please read through
the operating instructions completely, follow the
Safety Instructions
in this manual as well as the gen-
eral
Safety Instructions for Power Tools
in the
accompanying booklet.
Important instructions, which should be read
before starting operation, and which we strongly
recommend observing:
If the mains cable is damaged while working, pull
the mains plug immediately.
Never work with a damaged mains cable.
Wear protective glasses, hearing protection, pro-
tective gloves and sturdy shoes.
The dust that is produced while working is detri-
mental to health. Use dust extraction and wear a
dust mask.
The machine must be used only for dry cutting/
grinding.
Do not work with materials containing asbestos.
Do not carry the machine by the cable.
Always hold the machine firmly in both hands and
take a firm stance.
Always conduct the cable away to the rear of the
machine.
Only insert the mains plug into the socket when
the machine is turned Off.
If the mains plug is pulled out, of if there is a power
cut, unlock the On/Off switch immediately and set
it to the Off position in order to prevent it from
starting to run again in an uncontrolled manner.
The auxiliary handle serves for your safety. Work
with the additional handle mounted.
Only do cutting and grinding work with the protec-
tive guard mounted!
The dust produced when treating stone with crys-
talline silicic acid is hazardous to health. Use a
dust extractor and wear a dust mask. The dust
extractor must be suitable for vacuuming stone.
For clamping the grinding discs, clamping flanges
may only be used that are the same size and
shaped to fit the contacting surface. Please
observe the instructions for using the clamping
flange in the operating manual. Intermediate
layers may not be used on conical or depressed-
centre grinding discs.
When clamping depressed-centre grinding tools
the diameter of the clamping flange must be at
least 5 mm smaller than the diameter of the flat
depressed-centre surface of the grinding tool;
here, the clamping flange must not press onto the
transitional radius of the clearance.
The location bore of the grinding tools may not be
drilled afterwards as there is risk of fracture.
Grinding tools may on no account be operated at
a speed higher than that stipulated by the grinding
tool manufacturer.
Only fibre-reinforced grinding discs or diamond
cutting discs may be used.
The grinding discs etc. intended for use must be
approved for a peripheral velocity of 80 m/s!
Formula:
d = Diameter of the grinding disc in mm
n = No-load speed/min.
(see identification plate)
m/s = Peripheral velocity in metres per second
A new grinding tool and any grinding tool that is
re-mounted, must run on the machine intended for
use at no-load for 30 seconds. Operating person-
nel and any other persons must stand outside the
danger area during the test run.
The machine may only be brought into contact
with the work piece once it has been switched on.
Caution! Be careful of rotating grinding tools.
Pay attention to the direction of rotation: Always
hold the machine such that the grinding dust or
sparks fly away from the body. When grinding
metal, sparks can occur. Be careful if persons or
objects are standing nearby. Inflammable material
must not be kept in the vicinity.
Check the working area with a metal detector in
order to avoid damaging any concealed electrical
leads, or water and gas pipes.
Switch the machine off immediately if the cutting
disc should jam (jerky reaction force).
Do not use any cutting discs for rough grinding.
Grinding tools may not be brought to a standstill
by pressing against the periphery or grinding face
of the grinding tool.
Do not clamp the machine in a vice.
Observe the instructions for assembly and opera-
tion provided by the manufacturer of the grinding
tool.
1 Application
2
Safety Instructions and
Accident Prevention
d · 3.14 · n = m/s
6000
900 WTSE - Buch Seite 8 Donnerstag, 28. Juni 2001 2:52 14
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kress wts 900 e at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kress wts 900 e in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info