819057
13
Zoom out
Zoom in
Previous page
1/332
Next page
EN
13
3. For lifting the mower, it is recommended that two
people lift from each side of the mower using the
motor guard and lower handle connection areas
as handles.
When lifting the machine in the folded state,
grasp the motor guard, not the handles.(See Fig.
L)
L
Transporting the battery
1. Ensure the battery is in a safe condition.
2. Use non-conductive packaging when
transporting the battery.
3. The contained Li-Ion batteries are subject to the
dangerous goods legislation requirements.
Transport batteries only when the battery
housing is undamaged. Pack up the batteries in
such a manner that cannot move around in the
packaging.
MAINTENANCE
WARNING!
Stop the mower and remove the
battery before removing the grass collection
bag.
NOTE: To ensure long and reliable service, perform
the following maintenance procedures regularly.
Check for obvious defects such as a loose, dislodged
or a damaged blade, loose ttings, and worn or
damaged components. Check that the covers and
guards are all undamaged and are correctly attached
to mower. Carry out any necessary maintenance or
repairs before operating mower. If the mower should
happen to fail despite regular maintenance, please
call our customer helpline for advice.
BLADE SHARPENING
KEEP BLADE SHARP FOR BEST MOWER
PERFORMANCE. A DULL BLADE DOES NOT CUT
GRASS CLEANLY OR MULCH PROPERLY.
WEAR EYE PROTECTION AND ANTI-CUT
GLOVES WHILE REMOVING, SHARPENING, AND
INSTALLING BLADE.
NOTE: Sharpening or replacing the blade after every
50 hours.Sand causes the blade to dull quickly. If your
lawn has sandy soil, more frequent sharpening or
replacing may be required.
REPLACE BENT OR DAMAGED BLADE
IMMEDIATELY.
WHEN SHARPENING THE BLADE
1. Use a block of wood placed to prevent the blade
from turning.
2. Using the socket and wrench, remove the blade
bolt and then the blade.(See the blade removing
section)
3. Clamp the blade in a vice, or similar, to prevent it
from moving during sharpening.
4. Sharpen the cutting edges on both ends of the
blade. Ensure that the same amount of material
is removed from both ends to keep the blade
balanced.
5. Check the blade balance. (See the blade
balancing section)
6. Replace the blade in the reverse order of the
disassembly.
7. Make sure to tighten the blade bolt to the required
torque (25 Nm).
NOTE:
1. Be sure the mower is turned off and remove the
battery.
2. Tip the mower onto its side as shown in gure M1
M1
BLADE REMOVING (SEE FIG. M2)
M2
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kress KC720.9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kress KC720.9 in the language / languages: All languages as an attachment in your email.

The manual is 103.63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info