Manual Kress 900 hex (page 10 of 56) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish)

390125

Zoom out

Zoom in

1/56

10 English 900 HEX/2

Before any work on the machine itself, pull the

mains plug!

Selecting the rubber backing pad

The eccentric sander is fitted with an all-purpose

rubber backing pad of medium hardness. However,

rubber backing pads with varying degrees of hard-

ness may be fitted, depending on the type of applica-

tion (see application table):

Super-soft backing pad:

Suitable for polishing large surfaces and for particu-

larly sensitive sanding work (also curved surfaces).

Soft rubber backing pad:

All-purpose, suitable for all sanding work.

Hard rubber backing pad:

Suitable for high sanding performance, particularly on

large, flat surfaces.

Fitting the sanding tools (Fig. C)

The machine is fitted with a quick-change (connecting

link) system, enabling sanding tools to be changed

easily without the aid of an additional tool.

Before mounting any new sanding sheets 16, dust

and dirt must be removed from the backing pad 12.

Press the sanding sheets or polishing tools onto the

backing pad and make sure that the bore holes of the

sanding sheet match the bore holes on the backing

pad.

Only use original Kress sanding and polishing

tools with the pressure-sensitive connecting link.

Changing the rubber backing pad (Fig. C)

For changing the backing pad 12, remove it from its

carrier plate 15.

Damaged rubber backing pads must be replaced

immediately.

Changing the backing pad carrier plate

(Fig. D)

When changing the backing pad carrier plate 15, pull

off the sanding sheet or polishing tool, respectively.

Loosen screw 17 with a Torx screwdriver and remove.

Hold the backing pad carrier plate 15 firmly and

tighten the screw 17 firmly with a Torx screwdriver.

Dust extraction prevents large accumulations of dust,

high concentrations of dust in the ambient air and

facilitates disposal.

For long periods of working with wood or for commer-

cial use on materials that produce dust that is detri-

mental to health, the machine is to be connected to

a suitable external dust extraction device.

Adapter for vacuum cleaner connection

The adapter enables the sanding dust to be vacu-

umed using a normal household vacuum cleaner.

The rubber reducer can be used for reducing the con-

nection diameter on the diameter of the vacuum

cleaner tube.

Mounting the dust bag (Fig. B)

For smaller sanding jobs the dust bag supplied with

the machine can be used for dust extraction. The

machine has its own effective dust extraction facility

with integrated suction turbine and dust bag.

Push the dust bag with the locking connection 14 from

behind onto the mounting on the blower flange and

press it on. The locking connection engages by spring

pressure.

The dust bag can be taken off by pulling the moulded-

on grip.

The dust bag must be emptied as soon as the suction

strength slackens. To do this, pull the clamp off in the

direction of the arrow and push it on again after emp-

tying.

Sanding surfaces

Only perfect sanding sheets will give a good sanding

performance and protect the machine.

Observe uniform feed. Less contact pressure gives

a better sanding performance and protects the

machine and sanding tools.

Different rubber backing pads and sanding wheels

should be used depending on the material.

The abrasive power and the sanding finish are deter-

mined primarily by the choice of sanding disc (grain),

speed of the rubber backing pad and contact pressure

(ssee application table).

Place the whole sanding area of the eccentric disc

sander onto the material which requires sanding.

Switch on the machine and move over the work-piece,

applying moderate pressure.

8 Inserting/Removing Tools 9 Dust extraction device

10 Practical Tips

900 HEX/2 - Buch Seite 10 Dienstag, 27. Juni 2000 8:06 08

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kress 900 hex in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kress 900 hex Manual

Product: