508056
14
Zoom out
Zoom in
Previous page
1/74
Next page
14 English 240 PAH
The tool holder 1 clamps the drilling tools without
using a tool key.
INSERTING TOOLS
Before all work on the machine itself,
always set the rotational direction switch 7
to the middle position.
Clean and lightly grease the tool shaft.
Pull back the unlocking collar 3. Insert the tool while
turning into the tool holder until it latches. Release the
unlocking collar. Check whether the tool is firmly
seated.
Take care that the dust protection cap 2 is not dam-
aged.
Replace damaged dust protection caps!
REMOVING TOOLS
Slide the unlocking collar 3 to the rear and pull out the
tool.
For drilling work in metal, wood and plastic with
drills that have normal shafts, a drill chuck (13 mm
max. chuck opening) is available. The drill chuck is
mounted on the adapter (accessory) for screwdriver
bits. All common drill chucks with 1/2" × 20 UNF
internal threads (13 mm max. chuck opening) can be
used.
MOUNTING THE CHUCK
Before all work on the machine itself,
always set the rotational direction switch 7
to the middle position.
Clean the threads of the drill chuck (accessory) and
the adapter 18 (see accessory). Screw the drill chuck
onto the adapter and tighten firmly (approx. 30 Nm).
Clamp in a vise for tightening the adapter, for exam-
ple. Clamp an Allen key in the drill chuck and use it to
tighten the chuck. Then lock the adapter in the tool
holder the same as a drill.
Do not drill into hidden electrical
lines or gas and water pipes.
Check the area to be worked with a
metal detector, for example, before
starting.
For metal, use only flawless, sharpened drills; for
stone and concrete, only masonry drills with hard
metal inserts.
Always adapt the speed to the material to be worked
and the diameter of the drill. For precision working
with metal and wood, place the machine in a drill
stand (accessory).
HAMMER- DRILLING
Wear protective glasses and
hearing protection.
Do not apply to much pressure.
The performance is not increased
in this manner.
For hammer drilling, work only with protective
glasses, hearing protection and the auxiliary
handle 10. Check before putting into operation if
the shift knob 4 is latched in the position.
DRILLING IN TILES
Start drilling slowly on the tile. After the tile is drilled
through, switch to impact drilling.
SCREWDRIVING
Screwdriver bits can be inserted into the adapter 18
(see accessory). Commercially available bits with a
hexagonal dimension of 6.3 mm or 1/4" (DIN 3126,
Form C) can be used.
The screwdriver bits are held in the adapter with a
spring ring. Therefore, use only bits with a notch.
9 Inserting/Removing Tools
10 Drill Chuck (Accessory)
Fett
3
11 Practical Tips
240 PAH - Buch Seite 14 Mittwoch, 30. Januar 2002 1:57 13
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kress 240 PAH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kress 240 PAH in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info