508056
13
Zoom out
Zoom in
Previous page
1/74
Next page
240 PAH English 13
If the batteries cannot be charged correctly:
1. Make sure the socket is providing voltage.
2. Make sure the charging points provide good
contact.
3. Should charging still not be possible, please send
the battery and battery charger to our nearest serv-
ice centre.
Wall Mounting of the Charging Unit
The charging unit can be attached to the wall with
the aid of the wall holder 19 provided and standard
screws.
The charging unit can be removed again at any time
by lifting and unhooking and used as a table unit, for
example.
Notes for the correct use of the battery:
To obtain the maximum service life, do not
recharge the battery immediately after a short
period of use but, if possible, discharge to the
lower capacity limit and then recharge.
Avoid to the extent possible the blocking of the
machine. The resulting excessive current flow
leads to quick discharging and increased wear of
the battery.
An increasingly shorter operating time per recharg-
ing of the battery is an indication that the battery is
worn out and must be replaced.
Do not carry out any repair on the charger yourself!
As a basic rule, return the faulty machine to our next
customer service centre (also in the case of defective
mains cables)!
Convince yourself before using that the battery is
securely seated in the machine.
SWITCHING ON/OFF
Press or release the On/Off switch 6.
DRILLING - IMPACT DRILLING
For drilling, place the selector 4 in the position.
For impact drilling, set to .
The switch-over can best be performed at a standstill.
Only after the On/Off switch 6 is actuated and the
machine starts does the gear box shift to the selected
mode.
Note: Left rotation when impact drilling damages the
drill. Switch off the impact mechanism for diamond
crown drilling or for mixing work.
When hammer drilling, use exclusively drills with
hard metal inserts and SDS-Plus shafts. The use of
commercially available masonry drills with cylindrical
shafts by means of the adapter 18 and the normal drill
chuck in conjunction with the pneumatic impact mech-
anism is not possible.
SPEED CONTROL
With the On/Off switch 6, the speed
can be continuously varied. With
light pressure on the On/Off
switch 6, the machine begins to
rotate slowly; with increased pres-
sure, the speed increases.
ROTATIONAL DIRECTION SWITCHING
Operate the rotational direction
switch 7 only when the machine is
at a standstill!
Take hold of the rotational direction
switch 7 on both sides.
Right rotation: Set the rotational direction switch 7
to “R”.
Left rotation: Set the rotational direction switch 7
to “L”.
Important! Press the rotational direction switch 7 in
each case to the stop on the housing, i. e. until it can
be felt to engage.
If the rotational direction switch 7 is set between
the positions “R” and “L”, the machine cannot be
switched on.
x = 185 mm
19
8 Putting into Operation
240 PAH - Buch Seite 13 Mittwoch, 30. Januar 2002 1:57 13
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kress 240 PAH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kress 240 PAH in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info