Manual Kress 1500 KS (page 9 of 56) (English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish)

508050

Zoom out

Zoom in

1/56

1500 KS English 9

Measured values determined according to

EN 50 144.

Sound pressure level: 100 dB (A)

Sound power level: 87 dB (A)

Workplace related emission value: 90 dB (A).

For operation, noise protection measures are

required.

The typical hand-arm vibration is below 2.5 m/s

Before any work on the machine itself, pull the

mains plug!

Operate the machine only with the auxiliary handle 7.

Connect the mains cable module to the handle. The

plug must latch.

Use the mains cable module provided only for

Kress Electro-Tools. Do not attempt to operate

other machines with the module.

Use only an original Kress mains cable module that is

at least of heavy rubber sheathed cable (Code desig-

nation H07 RN-F).

Checking the adjustment of the riving knife

The riving knife 15 must always be used for safety

reasons. The riving knife prevents the saw blade from

becoming jammed when making lengthwise cuts.

Introduce the gap rudder 15 into the pick-up attach-

ment of the protective hood and hold it there. Secure

the gap rudder 15 using the socket head bolt 17 and

any suitable underlay washer. At first only tighten the

socket head bolt 17 lightly.

The adjustment takes place at maximum cutting

depth.

Loosen screw 17, adjust the riving knife 15 and re-

tighten the screw (see figure).

Cutting Depth Adjustment

The depth of the cut can be set up to 65 mm at

scale 19. When you loosen the two wing nuts 6, the

entire base can be moved up or down in the parallel

guides to set the desired cutting depth. Retighten wing

nuts 6 after you make the setting. In order to prevent

accidents and get a clean cut, make sure that the

blade does not project farther than the height of a

blade tooth out of the opposite side of the work.

Reducing cutting depth

After loosening the two wing nuts 6, one half turn is

enough, hold saw housing with both hands and push

guide arm of parallel guide with both thumbs to the

rear until the line mark is at the desired adjusting point

on scale.

Tighten wing nut 6. Check mark on second guide arm

and also tighten second wing nut.

Increasing cutting depth

After loosening wing nuts 6 hold machine with one

hand at front on handle or on housing and with the

other hand on saw table 13 and push both compo-

nents against each other until the line mark indicates

that the desired adjustment on the scale has been

attained. Tighten wing nuts 6.

3 Technical Data

Hand Circular Saw 1500 KS

Input power 1 500 Watt

Output power 900 Watt

On-off switch with lock off safety

position

•

No-load speed 4 700 RPM

Speed under load 3 640 RPM

Saw blade-ø, max. 190 mm

Saw blade-ø, min. 177 mm

Saw blade-/tooth

thickness, max. 2.25/2.6 mm

Saw blade-/tooth

thickness, min. 1.5/1.5 mm

Mounting hole 20 mm

Riving knife thickness, max. 1.5 mm

Max. cutting depth at 90° 65 mm

at ø 190 mm

Max. cutting depth at 45° 44 mm

at ø 190 mm

Base dimensions (Base plate) 162 x 335 mm

Weight approx. 5.5 kg

Protection class II/

4 Noise/vibration information

Mounting the Auxiliary Handle and

the Mains Cable Module

6 Before use

2,5 - 5 mm

1500 KS.book Seite 9 Montag, 15. April 2002 11:11 11

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kress 1500 KS in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kress 1500 KS Manual

Product: