508050

Kress 1500 KS Manual

8
Zoom out
Zoom in
Previous page
1/56
Next page
8
English 1500 KS
Application
The circular saw is an all-purpose saw for cutting soft
and hard woods, chipboard, plywood, plastics,
resopal-coated materials.
Before putting the machine into operation, read
through these operating instructions completely and
observe the safety instructions contained therein as
well as those in the enclosed booklet on general
safety instructions for electro-tools.
If the mains cable is damaged while working, pull
the mains plug immediately.
Never work with a damaged mains cable.
For safety reasons, work only with the auxiliary
handle
7
mounted.
Do not carry the machine by the cable.
The mains receptacles in the working area must be
protected by a residual current circuit breaker (RC).
For the attachment of identification markings on the
machine, do not drill into the housing. The protec-
tive insulation would be shorted. Use stickers.
Wear protective goggles, ear protectors and face
mask.
Wear protective gloves and sturdy shoes.
For long hair, wear hair protection. Work only with
close-fitting clothes.
The machine must be operated only with the asso-
ciated protective devices.
Always use the riving knife
15
.
The swinging guard
12
must be able to move
freely. It must not become jammed in the opened
state.
For stationary use, the machine may be operated
only on a sawing table with restarting protection.
Always direct the cable to the rear away from the
machine.
Connect machines that are used in the open via a
residual current circuit breaker with a triggering
current of 30 mA maximum. Use only extension
cables that are intended for outdoor use and are
protected against splash water.
Cracked or distorted blades may not be used. Work
only with good sharp blades.
Never use high-alloy HSS blades with this circular
saw.
Saw blades which are not in accordance with the
specifications stated in these operating instructions
may not be used.
Only use blades whose hub thickness is not
greater than and whose tooth offset width is not
less than the width of the gap rudder.
Insert the mains plug only when the machine is
switched off. The device must be always switched
on and off with the trigger switch and never by pull-
ing out or inserting the plug at the socket or by pull-
ing out/inserting the mains cable on the machine.
When working, always guide the machine away
from the body.
The cutting path must be free of obstacles both
above and blow. Do not saw into nails, screws, etc.
The saw blade should not protrude below the work-
piece more than
3 mm
.
Keep hands clear of the rotating saw blade. Do not
come into contact with the rotating saw blade on
the underside of the workpiece.
Do not stick fingers into the sawdust ejector
18
.
Do not work with materials containing asbestos.
Do not tilt the saw blade.
If the saw blade jams, switch off the machine imme-
diately.
After switching off, do not brake the saw blade to a
stop by applying side pressure.
1
Latch for mains cable module
2
Safety lock off button
3
On-off switch with lock off safety position
4
Pin for spindle lock
5
Ventilation slots
6
Wing-nut (to set cutting depth)
7
Helper handle
8
Clamp lever (for setting the cutting angle)
9
Cutting angle scale
10
Star grip bolt for parallel stop
11
Parallel guide
12
Swinging protective guard
13
Base
14
Eye shield
15
Riving knife
16
Upper guard
17
Riving knife screw
18
Sawdust ejector (suction neck)
19
Cutting depth scale
Accessories illustrated or described are not always
included as standard delivery items.
1
Safety Instructions and
Accident Prevention
2 Illustration
1500 KS.book Seite 8 Montag, 15. April 2002 11:11 11
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kress 1500 KS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kress 1500 KS in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,62 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info