Manual Kress 133 MDX (page 12 of 63) (English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish)

508042

Zoom out

Zoom in

1/63

English 133 MDX

Mechanical 2-speed selector

For battery equipment, the mechanical 2-speed selec-

tor permits optimal drilling torques of 0–1500 rpm in

2nd speed and with high transmission in 1st speed

(0–450 rpm) very high tractive power even with

screws of a large diameter. The switchover is per-

formed by moving the switch

until it stops in position

1 or 2.

Torque selection

The battery-driven rotary screwdriver is equipped with

a seven-stage mechanical torque selection. The start-

ing torque for a particular screw is set at the adjusting

ring

according to the scale.

The volume of the torque is dependent on various fac-

tors – type and hardness of the material to be proc-

essed, type and length of the screws to be used, but

in addition the demands made on the screw connec-

tion. The data contained in the following table should

be observed as a guideline:

Stage 1 = approx. 1 Nm:

screws Ø 3 mm

Stage 2 = approx. 2 Nm:

screws Ø 3.5 mm

Stage 3 = approx. 3 Nm:

screws Ø 4 mm

Stage 4 = approx. 4 Nm:

screws Ø 4.5 mm

Stage 5 = approx. 5 Nm:

screws Ø 5 mm

Stage 6 = approx. 6 Nm:

screws Ø 5.5 mm

Stage 7 = approx. 7 Nm:

screws Ø 6 mm

When the set torque is reached it is signalled acousti-

cally through the construction of the torque coupling.

The coupling disengages with a click.

Operation of the

Quick Clamping Drill Chuck

Rotational direction switch in the LOCK position

■

The fully automatic spindle locking makes possible

quick and easy changing of the tool in the drill chuck.

Opening: Turn the sleeve in the “AUF” direction.

Clamping: Open the chuck and insert the tool as far

as possible.

Firmly clamp the chuck by turning the

sleeve in the “ZU” direction.

For soft drill shafts, it may be necessary to retighten

after a short time.

Caution! For reasons of safety, take the bat-

tery out of the device for all installation and

removal operations!

Drilling

When drilling, set the torque ring to the

“drill”

symbol.

The torque coupling is deactivated. Maximum torque

is available for drilling.

When drilling steel, take care that no swarf

enters the ventilation slits of the housing, as

these are attracted by the permanently active

magnet of the motor and would remain on the

motor.

Screwing

Make sure that the bit and screw correspond in size

and shape.

It is advisable to use socket-head screws since their

self-centering action ensures safe work.

Or even better – TORX screws and the corresponding

bits. Optimal screwing is achieved when the screwing

device is fixed securely in the screw head.

Dismounting the Drill Chuck

Rotational direction switch in the LOCK position

■

Remove the left-hand threaded screw that secures

the drill chuck on the drill spindle against unscrewing

in left rotation. The drill chuck can then be loosened

by lightly striking a Allen key clamped in the drill chuck

and screwed off.

Remounting takes place in the reverse order.

Clean the flat surfaces on the drill chuck and spindle

before mounting. Screw on the drill chuck firmly and

secure with the safety screw.

Observe in addition that, when using a rim gear drill

chuck, the chuck key must not be attached to the

machine with chains, cords or similar means.

When drilling or screwdriving, secure the work

pieces against being rotated by the drill.

8 Practical Tips

133 MDX - GB Seite 12 Freitag, 24. März 2000 8:42 08

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Kress 133 MDX in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,35 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Kress 133 MDX Manual

Product: