813952

Kratki Antares Manual

23
Zoom out
Zoom in
Previous page
1/338
Next page
23
EN
Prohibited Fuel
The following is not allowed to be burned in the heaters: minerals, e.g. coal, tropical wood (like maho-
gany), chemical products and uids, (like oil, alcohol, petrol, and naphthalene), laminated boards, or
adhesive-bonded, impregnated or pressed wood chips and litter. If any other fuel is allowed, it will be
notied on the rating plate.
Avoid lling the hearth with wood fully, optimising the amount of fuel at one-third of the combustion
chamber’s capacity. Before you replenish the wood, wait until the ames have died down; do not add
wood onto too much heat. After you light the re, make sure you replenish the wood in the combu-
stion chamber by putting fuel inside so that the chamber is lled in a reasonable way for the intended
burning time determined by the user, based on his/her individual experience.
Close the door each time. After a long period of non-use, a lower output startup is recommended.
FIREPLACE-FIREBOX ASSEMBLY AND INSTALLATION
The installation of the heater must be carried out by a person who is suciently qualied to conduct
assembly and installation work of this kind. This is a prerequisite for safe replace rebox use. The in-
staller must conrm correct assembly and installation execution in the guarantee certicate by signing
and sealing it. Failure to comply with this requirement will void all the Buyer’s warranty claims against
the heater manufacturer.
PREPARATION FOR INSTALLATION
The heater is delivered in a ready-to-be-installed state. Remove the packaging and check the appliance
for completeness according to this Operation Manual. You should also ensure that the following are
operational
• The control of the air supply for the combustion chamber (ash trap);
• The correct functioning of closing the front door (hinges, handle);
• The ue and smoke pipe durability must have a re-resistance rating of a min. of 1 hr;
• The heater may be installed only after the smoke-duct chimney-sweep report has been completed.
CONNECTION TO CHIMNEY STACK
A free-standing stove must be connected to an individual chimney ue.
The minimum chimney draughts for rated heat output [Pa]: the chimney-draught values
- Minimum draught: 6 ± 1 Pa
- Medium, recommended draught: 12 ± 2 Pa
- Maximum draught: 15 ± 2 Pa
The chimney must be air-tight and its walls without any obstacles. Clean it of any soot and other dirt
before connecting. The connection between the chimney and the appliance must be air-tight, made of
non-ammable materials, and protected against oxidation (e.g. enamel-steel ue liner). If the chimney
generates a poor draught, consider installing new ducts. It is also important that the chimney does not
generate too much draught, but, if so, install a chimney-draught stabiliser. Alternatively, install special
chimney terminations for the draught control. The inspection of the chimney ue must be contracted
to a master chimney sweep, and any conversions are allowed to be made by an authorised service only,
so that all requirements are met.
The chimney ues must be connected in accordance with the relevant standards. The ue-gas stacks
must have an eective height of 4-6 lin. m.
The length of the connection to the chimney stack should not be more than 1/4 of the total stack
height.
Examples of stack connection
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Kratki Antares at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Kratki Antares in the language / languages: English, German, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info